A car is being driven at a rate of 60 ft/sec when the brakes are applied. The car decelerates at a constant rate of 19

The refractive index of the glass is 1.36. The answer is (b)

The refractive index of a material is the ratio of the speed of light in vacuum to the speed of light in the material.

Using Snell's law, the ratio of the sine of the angle of incidence to the sine of the angle of refraction can be expressed as the ratio of the refractive indices of the two materials.

Therefore, we can use this relationship to solve for the refractive index of the glass.

Let ng be the refractive index of the glass. Using the given information, we can write:

sinθ1/sinθ2 = ng/1.50 = λ1/λ2

where θ1 and θ2 are the angles of incidence and refraction, λ1 is the wavelength in the glass, and λ2 is the wavelength in benzene.

Solving for ng, we have:

ng = (1.50 × λ1) / λ2 = (1.50 × 455 nm) / 500 nm ≈ 1.36

Therefore, the answer is (b) 1.36.

To know more about Snell's law, refer here:

https://brainly.com/question/2273464#

#SPJ11

The statement " The centroidal axis and neutral axis are always the same in both straight and curved beam" is false.

In straight beams, the centroidal axis and neutral axis are coincident because the cross-section of a straight beam is symmetric about the centroidal axis. However, in curved beams, the centroidal axis and neutral axis may not coincide because the cross-sectional area of a curved beam is not symmetric about the centroidal axis.

The neutral axis of a curved beam is the axis passing through the centroid of the cross-sectional area that is subjected to zero stress when the beam is loaded. In general, the neutral axis of a curved beam is located at a distance from the centroidal axis that depends on the curvature of the beam and the shape of the cross-section.

To know more about the beams refer here :

https://brainly.com/question/3132489#

#SPJ11

The normal force at A is 98.1 N, and the frictional force at A is 49.05 N.

To determine the normal and frictional forces at A, follow these steps:
1. Calculate the gravitational force acting on the disk: F_gravity = mass × g = 10 kg × 9.81 m/s² = 98.1 N.
2. Determine the vertical component of the gravitational force acting on point A: F_vertical = F_gravity × cos(θ) = 98.1 N × cos(60°) = 49.05 N.
3. Calculate the normal force at A: F_normal = F_gravity - F_vertical = 98.1 N - 49.05 N = 98.1 N (since the disk is in equilibrium).
4. Calculate the torque caused by friction: τ = I × α, where I is the moment of inertia and α is the angular acceleration. Since the disk does not slip, α = 0, so τ = 0.
5. As there's no net torque, the frictional force must be equal to the vertical component of the gravitational force: F_friction = F_vertical = 49.05 N.

Learn more about friction here:

https://brainly.com/question/13000653

#SPJ11

If the sonar pulse suddenly takes longer to return to the ship, it suggests that there is an increase in the distance between the ship and the ocean floor or an increase in the speed of sound in the water.

Here are a couple of possibilities:

1. The ship has moved farther away from the ocean floor: If the ship has moved to a greater distance from the ocean floor, it will take a longer time for the sonar pulse to travel to the bottom and back to the ship. This could occur if the ship is moving away from the location where the initial pulse was sent or if the ship is in motion and has increased its distance from the ocean floor.

2. There is a change in the speed of sound in water: The speed of sound in water can be affected by various factors such as temperature, salinity, and pressure. If any of these factors change, the speed of sound in water can also change. If the speed of sound in the water has increased, it will take a longer time for the sonar pulse to travel to the bottom and back to the ship, resulting in a longer return time.

To determine the exact cause of the longer return time, further investigation and analysis of the situation would be necessary.

To know more about sonar pulse here

https://brainly.com/question/32005904

#SPJ4

The magnitude of the average acceleration that stopped the car can be calculated using the formula a = ∆v/∆t, where ∆v is the change in velocity and ∆t is the time taken to stop the car. Plugging in the values, we get a = -22/3.8 = -5.79 m/s^2 (the negative sign indicates deceleration).

The initial speed of the 1000-kg car in mph can be found by converting 22 m/s to mph, which is approximately 49.2 mph. The initial kinetic energy of the car can be calculated using the formula KE = 0.5*m*v^2, where m is the mass of the car and v is its velocity. Plugging in the values, we get KE = 0.5*1000*(22^2) = 242000 kJ.
The initial momentum of the car can be calculated using the formula p = m*v, where m is the mass of the car and v is its velocity. Plugging in the values, we get p = 1000*22 = 22000 kg*m/s. The magnitude of the impulse necessary to stop the car can be calculated using the formula J = ∆p, where ∆p is the change in momentum. Since the car comes to a complete stop, the change in momentum is simply the initial momentum, which is 22000 kg*m/s.

Therefore, the magnitude of the impulse is also 22000 kg*m/s. The magnitude of the average force in kiloNewtons (kN) that stopped the car can be calculated using the formula F = ∆p/∆t, where ∆p is the change in momentum and ∆t is the time taken to stop the car. Plugging in the values, we get F = 22000/3.8 = 5789.5 N = 5.7895 kN.

To know more about acceleration visit:

https://brainly.com/question/30660316

#SPJ11

Therefore, the required factors to solve for the nonstandard cell potential using the Nernst equation are the standard cell potential, temperature, and concentrations of the species involved.

To solve for the nonstandard cell potential using the Nernst equation, the following factors are required:

Standard cell potential (E°): The standard reduction potential of the half-reactions involved in the cell reaction is needed. It provides a reference point for the calculation.

Temperature (T): The temperature at which the cell operates is required because the Nernst equation includes a term for temperature dependence.

Concentrations of species involved: The concentrations of the species participating in the cell reaction are necessary to calculate the nonstandard cell potential. The Nernst equation incorporates the logarithm of the concentration ratio.

Learn more about Nernst equation here:

https://brainly.com/question/32075126

#SPJ11

For a given compression ratio, the thermal efficiency of the Otto cycle will be highest when the working fluid has the highest ratio of specific heats. In this case, argon has the highest ratio of specific heats and therefore it will give the highest thermal efficiency.

The thermal efficiency of an Otto cycle is given by:

η = 1 - (1/r)^(γ-1)

where r is the compression ratio and γ is the ratio of specific heats.

The thermal efficiency depends only on the compression ratio and the ratio of specific heats of the working fluid. Therefore, the working fluid itself does not affect the thermal efficiency. However, the ratio of specific heats is different for each of the three fluids:

For air, γ = 1.4

For argon, γ = 1.67

For ethane, γ = 1.25

For more question on thermal efficiency click on

https://brainly.com/question/24244642

#SPJ11

The thermal efficiency will be highest for ethane as the working fluid.

The thermal efficiency of the ideal Otto cycle is given by:

η = 1 - (1/r)^(γ-1)

where r is the compression ratio and γ is the ratio of specific heats for the working fluid.

For a given compression ratio, the thermal efficiency of the Otto cycle depends on the value of γ, which is different for different working fluids.

For air, γ = 1.4

For argon, γ = 1.67

For ethane, γ = 1.22

Using these values, we can calculate the thermal efficiency for each case and compare them.

Assuming the same compression ratio for all cases, the thermal efficiencies are:

η_air = [tex]1 - (1/r)^(0.4)[/tex]

η_argon =[tex]1 - (1/r)^{(0.67)[/tex]

η_ethane = [tex]1 - (1/r)^{(0.22)[/tex]

To determine which working fluid will give the highest thermal efficiency, we need to compare these values.

Since the exponent in the expression for thermal efficiency is smaller for ethane, it means that it has a higher thermal efficiency than air and argon for the same compression ratio.

Learn more about thermal efficiency here:

https://brainly.com/question/13039990

#SPJ11

Answer:The statement "δH for an endothermic reaction is positive" is true.

The statement "δH for an exothermic reaction is positive" is false.

Explanation: ΔH (delta H) represents the change in enthalpy of a reaction. For an endothermic reaction, energy is absorbed from the surroundings, resulting in an increase in the internal energy of the system, and therefore ΔH is positive. In contrast, for an exothermic reaction, energy is released to the surroundings, resulting in a decrease in the internal energy of the system, and therefore ΔH is negative.

learn more about endothermic reaction

https://brainly.com/question/28909381?referrer=searchResults

#SPJ11

The current flowing through the 55 watt light bulb is approximately 0.5 amps.

To calculate the current flowing through the light bulb, we can use Ohm’s law, which states that the current (I) flowing through a circuit is equal to the voltage (V) divided by the resistance ®. In this case, we are given the power (P) of the light bulb, which is 55 watts, and the voltage (V) of the circuit, which is 110 volts. Since power is equal to the product of voltage and current (P = V * I), we can rearrange the equation to solve for the current:

I = P / V

Substituting the given values, we have:

I = 55 watts / 110 volts

I ≈ 0.5 amps

Therefore, the current flowing through the 55 watt light bulb is approximately 0.5 amps.

It’s important to note that the power rating of a light bulb (in watts) indicates the rate at which it consumes electrical energy, while the current (in amps) represents the rate at which the electric charge flows through the circuit. In this case, the power rating is used to calculate the current flowing through the light bulb.

Learn more about Ohm’s law here:

https://brainly.com/question/1247379

#SPJ11

The opal's index of refraction is 1.45 based on speed of light.

To find the opal's index of refraction, we need to use the formula:

Index of refraction = speed of light in a vacuum / speed of light in the material

We know that the speed of light in air (which is close to a vacuum) is [tex]2.07*10^8 m/s[/tex]. To find the speed of light in the opal, we need to know the opal's index of refraction.

Let's call the opal's index of refraction "n". Then we can write:

n = speed of light in a vacuum / speed of light in the opal

We can rearrange this equation to solve for n:

n = speed of light in a vacuum / (speed of light in air / opal's refractive index)

[tex]n = 2.9979*10^8 m/s / (2.07*10^8 m/s / n)\\n = 2.9979*10^8 m/s * n / 2.07*10^8 m/s[/tex]

n = 1.45

Therefore, the opal's index of refraction is 1.45.

Learn more about refraction here:

https://brainly.com/question/16038622

#SPJ11

Answer:

Explanation:

There could be several reasons why the fridge magnets are not attaching to the fridge. Here are a few possible explanations:

Material: The magnets you purchased might not be made of a magnetic material. Some souvenirs may look like magnets but are only decorative and lack the magnetic properties required to stick to metal surfaces like a fridge.

Magnetic strength: The magnets you bought may have weak magnetic strength, making them unable to attach to the fridge. Magnets vary in their strength, and if the ones you have are not powerful enough, they may not adhere to the fridge's surface.

Fridge surface: The surface of your fridge may not be magnetic. While many fridges have magnetic surfaces, some newer models or specialized fridges may have non-magnetic materials, such as stainless steel or plastic, which won't hold magnets.

Protective coating: If your fridge has a protective coating or a layer of paint, it might interfere with the magnetic force. The magnets need direct contact with the metal surface to adhere, and any barrier between the magnet and the fridge can prevent attachment.

Incorrect positioning: It's also possible that you are not placing the magnets correctly on the fridge. Make sure you are placing them on a flat, smooth surface without any obstructions or unevenness that could prevent proper contact.

Dirty or greasy surface: If the surface of your fridge is dirty, greasy, or covered with dust, it can create a barrier between the magnet and the fridge, making it difficult for them to stick. Clean the surface with a mild detergent or cleaner to remove any dirt or grease.

It's worth noting that the effectiveness of fridge magnets can vary, and sometimes a combination of factors can contribute to them not sticking. If none of the above reasons seem to apply, it may be necessary to consider alternative options or consult the manufacturer of the fridge for more information.

Work output is 2600 J, Thermal efficiency is 28.26%.

To determine the mechanical work output and thermal efficiency of the engine, we need to use the first law of thermodynamics, which states that energy input equals the sum of energy output and work done.

Given:

Heat input (Qin) = 9200 J

Heat output (Qout) = 6600 J

Mechanical work output (W) can be calculated using the equation:

W = Qin - Qout

Substituting the given values:

W = 9200 J - 6600 J

W = 2600 J

The mechanical work output of the engine during one cycle is 2600 J.

Thermal efficiency (η) can be calculated using the equation:

η = (W / Qin) * 100

Substituting the values:

η = (2600 J / 9200 J) * 100

η ≈ 28.26%

Therefore, the thermal efficiency of the engine is approximately 28.26%.

Learn more about mechanical work

brainly.com/question/28012677

#SPJ11

The total resistance of the circuit when three 35-ω lightbulbs and three 75-ω lightbulbs are connected in series can be found by adding up the resistance of each individual bulb.  

When lightbulbs are connected in series, the total resistance of the circuit increases because the current must pass through each bulb before returning to the power source. As a result, the resistance of each bulb adds up to create a higher overall resistance for the circuit. To calculate the total resistance of a series circuit, we simply add up the resistance of each individual component. In this case, we have two sets of three bulbs, so we need to calculate the resistance of each set separately before adding them together.

When lightbulbs are connected in series, you simply add their individual resistances together. So for this circuit:
Total resistance = (3 x 35) + (3 x 75) = 105 + 225 = 330 ohms.
When lightbulbs are connected in parallel, you need to calculate the reciprocal of the total resistance:
1/R_total = 1/R1 + 1/R2 + ... + 1/Rn.
For this circuit:
1/R_total = (3 x 1/35) + (3 x 1/75) = 3/35 + 3/75 = 0.194,
R_total = 1 / 0.194 ≈ 15.97 ohms.

To know more about circuit visit:

https://brainly.com/question/27206933

#SPJ11

To calculate the average translational kinetic energy of a molecule in an ideal gas, we can use the equation:
E = (3/2) kT,,   E = 8.31 x 10^-21 J

where E is the average translational kinetic energy, k is the Boltzmann constant (1.38 x 10^-23 J/K), and T is the temperature in Kelvin.

Substituting the given temperature of 320 K into the equation, we get:

E = (3/2) x (1.38 x 10^-23 J/K) x (320 K)

E = 8.31 x 10^-21 J

Therefore, the correct answer is option D, 6.6 x 10^-21 J is closest to the calculated value. This means that the average translational kinetic energy of one molecule in the given ideal gas at 320 K is approximately 6.6 x 10^-21 J.
To calculate the average translational kinetic energy of a molecule in an ideal gas, we can use the following equation:

Average translational kinetic energy = (3/2) * k * T

where k is Boltzmann's constant (1.38 × 10⁻²³ J/K) and T is the temperature in Kelvin.

Given that the temperature T is 320 K, we can plug the values into the equation:

Average translational kinetic energy = (3/2) * (1.38 × 10⁻²³ J/K) * (320 K)

Now, we can calculate the result:

Average translational kinetic energy = (3/2) * (1.38 × 10⁻²³ J/K) * (320 K) ≈ 6.6 × 10⁻²¹ J

So, the average translational kinetic energy of one molecule in the ideal gas is approximately 6.6 × 10⁻²¹ J. Therefore, the correct answer is D. 6.6 × 10⁻²¹.

For more information on Boltzmann's constant visit:

brainly.com/question/30639301

#SPJ11

The fringe spacing in a double-slit experiment decreases as the wavelength of the light decreases, the spacing between the slits decreases, and the distance to the screen decreases. The difference in path length between the dot on the screen in the center of fringe E and the left slit is (3λd)/(2θ).

a. If the wavelength of the light is decreased, the fringe spacing will decrease. This is because fringe spacing is directly proportional to the wavelength of light.

b. If the spacing between the slits is decreased, the fringe spacing will increase. This is because fringe spacing is inversely proportional to the slit spacing.

c. If the distance to the screen is decreased, the fringe spacing will increase. This is because fringe spacing is inversely proportional to the distance between the slits and the screen.

d. Using the small angle approximation, the path difference between the dot in the center of fringe E and the left slit is approximately (d/2)sin(θ). The path difference to the right slit is the same but with the opposite sign for θ. The difference in path length is approximately d sin(θ) which equals 3λ/2. Assuming sin(θ) ≈ θ, the distance to the left slit is (3λd)/(2θ).

To know more about the double-slit experiment refer here :

https://brainly.com/question/30727105#

#SPJ11

The number of 22Na atoms in the initial sample N = 3.56 x 10¹² atoms. The activity of the sample is 1/4 of the initial activity: A = 7.5 x 10³ Bq.

The decay of radioactive isotopes follows an exponential decay law, which means that the amount of the radioactive substance remaining after a certain time can be expressed as a fraction of its initial amount. This fraction is determined by the isotope's half-life, which is the time it takes for half of the initial amount to decay.

In the case of 22Na, the half-life is 2.6 years. This means that after 2.6 years, half of the original 22Na atoms would have decayed, and only half would remain. After another 2.6 years, half of the remaining atoms would decay again, leaving only one-quarter (1/2 x 1/2 = 1/4) of the original number of atoms.

So, if the initial sample contained N atoms of 22Na, after two half-lives, the remaining number of atoms would be N/4. This exponential decay of radioactive isotopes is the basis of many applications in science and technology, such as radiocarbon dating and nuclear power generation.

To know more about atoms, refer here:

https://brainly.com/question/14644957#

#SPJ11

We put a negative sign in front of the answer because the total entropy of the universe is decreasing due to the irreversible transfer of heat.

To find the change in entropy of the universe, we need to use the formula ΔS = ΔS_hot + ΔS_cold, where ΔS_hot is the change in entropy of the hot reservoir and ΔS_cold is the change in entropy of the cold reservoir.
First, let's calculate the change in entropy of the hot reservoir. We can use the formula ΔS_hot = Q/T_hot, where Q is the heat transferred to the reservoir and T_hot is the temperature of the reservoir. Plugging in the values given in the problem, we get:
ΔS_hot = 1050 J / 576 K
ΔS_hot = 1.822 J/K
Next, let's calculate the change in entropy of the cold reservoir. We can use the same formula as before, but with the temperature and heat transfer for the cold reservoir. This gives us:
ΔS_cold = -1050 J / 305 K
ΔS_cold = -3.443 J/K
Note that we put a negative sign in front of the answer because heat is leaving the cold reservoir, which means its entropy is decreasing.
Now we can find the total change in entropy of the universe:
ΔS_univ = ΔS_hot + ΔS_cold
ΔS_univ = 1.822 J/K + (-3.443 J/K)
ΔS_univ = -1.621 J/K
Again, we put a negative sign in front of the answer because the total entropy of the universe is decreasing due to the irreversible transfer of heat.
To know more about entropy visit:

https://brainly.com/question/13135498

#SPJ11

To use the parallel axis theorem to calculate the total moment of inertia for a pendulum with a ball, we need to consider the individual moments of inertia and their distances from the axis of rotation.

The moment of inertia of the ball about an axis through the center of the ball is given as Iball = (2/5)mr^2, where m is the mass of the ball and r is the radius of the ball.

The total moment of inertia for the pendulum is the sum of the moment of inertia of the ball and the moment of inertia about the axis through the pivot.

Using the parallel axis theorem, the moment of inertia about the pivot axis can be calculated as follows:

I = Iball + mb^2

Where I is the total moment of inertia, m is the mass of the ball, b is the distance from the pivot at the top of the string to the center of mass of the ball.

Therefore, the total moment of inertia for the pendulum is I = (2/5)mr^2 + mb^2.

This equation takes into account both the rotation of the ball about its own axis and the rotation of the pendulum as a whole about the pivot point.

Learn more about the **parallel axis theorem** and its applications in physics here:

https://brainly.com/question/30460015?referrer=searchResults

#SPJ11

Part a: The de Broglie wavelength of the electron is 1.37 x 10^-10 meters.

Part b: The de Broglie wavelength of the proton with the same speed is 7.46 x 10^-8 meters.

Part A:

The de Broglie wavelength of an object with momentum p is given by the formula:

λ = h / p

where λ is the de Broglie wavelength, h is Planck's constant (6.626 x 10^-34 J*s), and p is the momentum of the object.

Since the electron has a mass of 9.109 x 10^-31 kg and a speed of 5.30 x 10^6 m/s, its momentum can be calculated as:

p = mv = (9.109 x 10^-31 kg) * (5.30 x 10^6 m/s) = 4.83 x 10^-24 kgm/s

Plugging this value of momentum into the de Broglie wavelength formula, we get:

λ = h / p = (6.626 x 10^-34 Js) / (4.83 x 10^-24 kgm/s) = 1.37 x 10^-10 m

Therefore, 1.37 x 10^-10 meters is the de Broglie wavelength of the electron.

Part B:

Following the same approach as above, the momentum of the proton with the same speed as the electron can be calculated as:

p = mv = (1.673 x 10^-27 kg) * (5.30 x 10^6 m/s) = 8.87 x 10^-21 kgm/s

Using this value in the de Broglie wavelength formula, we get:

λ = h / p = (6.626 x 10^-34 Js) / (8.87 x 10^-21 kgm/s) = 7.46 x 10^-8 m

Therefore, 7.46 x 10^-8 meters is the de Broglie wavelength of the proton.

For more such questions on de Broglie wavelength, click on:

https://brainly.com/question/30216495

#SPJ11

Part a: The de Broglie wavelength of the electron is 1.37 x 10^-10 meters.

Part b: The de Broglie wavelength of the proton with the same speed is 7.46 x 10^-8 meters.

Part A:

The de Broglie wavelength of an object with momentum p is given by the formula:

λ = h / p

where λ is the de Broglie wavelength, h is Planck's constant (6.626 x 10^-34 J*s), and p is the momentum of the object.

Since the electron has a mass of 9.109 x 10^-31 kg and a speed of 5.30 x 10^6 m/s, its momentum can be calculated as:

p = mv = (9.109 x 10^-31 kg) * (5.30 x 10^6 m/s) = 4.83 x 10^-24 kgm/s

Plugging this value of momentum into the de Broglie wavelength formula, we get:

λ = h / p = (6.626 x 10^-34 Js) / (4.83 x 10^-24 kgm/s) = 1.37 x 10^-10 m

Therefore, 1.37 x 10^-10 meters is the de Broglie wavelength of the electron.

Part B:

Following the same approach as above, the momentum of the proton with the same speed as the electron can be calculated as:

p = mv = (1.673 x 10^-27 kg) * (5.30 x 10^6 m/s) = 8.87 x 10^-21 kgm/s

Using this value in the de Broglie wavelength formula, we get:

λ = h / p = (6.626 x 10^-34 Js) / (8.87 x 10^-21 kgm/s) = 7.46 x 10^-8 m

Therefore, 7.46 x 10^-8 meters is the de Broglie wavelength of the proton.

For more such questions on de Broglie wavelength, click on:

brainly.com/question/30216495

#SPJ11

(a) To find the angle between the central maximum and next maximum of sound intensity, we can use the equation d sin θ = (m + 1/2)λ, where d is the distance between the slits, θ is the angle between the perpendicular bisector and the line connecting the slits to the central maximum, m is the order of the maximum (0 for the central maximum, 1 for the first maximum, etc.), and λ is the wavelength of the sound wave. Rearranging the equation, we get sin θ = (m + 1/2)λ/d. Plugging in the values given, we get sin θ = (1 + 1/2)(0.0171)/0.275, which gives us θ = 23.7°.

(b) To find the slit separation for microwaves, we can use the same equation as in part (a), but with the wavelength of the microwaves and the angle we just found. Rearranging, we get d = (m + 1/2)λ/sin θ. Plugging in the values, we get d = (1 + 1/2)(0.0275)/sin 23.7°, which gives us d = 0.053 cm.
(c) To find the frequency of light that would give the same angle between the central and next maximum of intensity, we can use the equation d sin θ = mλ, where d is the slit separation, θ is the angle we just found, m is the order of the maximum (0 for the central maximum, 1 for the first maximum, etc.), and λ is the wavelength of the light. Rearranging, we get λ = d sin θ/m. Plugging in the values, we get λ = (1.00 × 10^-6) sin 23.7°/1, which gives us λ = 3.81 × 10^-7 m. Using the speed of light (3 × 10^8 m/s), we can find the frequency: f = c/λ = 7.87 × 10^14 Hz, or 787 THz.

To know more about wavelength visit:

https://brainly.com/question/31143857

#SPJ11

The new temperature of the ideal gas after removing 3.6 J of thermal energy is approximately 12.1°C.

To calculate the new temperature, we'll use the formula for the change in internal energy of an ideal gas, which is ΔU = (3/2)nRΔT, where ΔU is the change in internal energy, n is the number of moles, R is the ideal gas constant, and ΔT is the change in temperature.

First, we need to determine the number of moles (n) from the given number of atoms (2.2 × 10²² atoms). Since 1 mole contains Avogadro's number (6.022 × 10²³) of atoms, we can find n by dividing the number of atoms by Avogadro's number:

n = (2.2 × 10²² atoms) / (6.022 × 10²³ atoms/mol) ≈ 0.0365 moles

Next, we need to find the change in internal energy (ΔU), which is -3.6 J since thermal energy is being removed from the gas.

Now, we can rearrange the formula ΔU = (3/2)nRΔT to solve for the change in temperature (ΔT):

ΔT = ΔU / [(3/2)nR] = -3.6 J / [(3/2)(0.0365 moles)(8.314 J/mol K)] ≈ -7.9°C

Since the initial temperature was 20°C, the new temperature is:

New Temperature = Initial Temperature + ΔT = 20°C -7.9°C ≈ 12.1°C.

To know more about the internal energy, click here;

https://brainly.com/question/14668303

#SPJ11

a)The wavelength of the electromagnetic waves needed for the first strong interference maximum in the Bragg reflection is 1.05 Å.

a2) Electromagnetic spectrum do these waves lie in  X-ray part .

a3) The second strong interference maximum occurs at an angle of 9.0°. We can repeat this process to find the angles for other maxima.

(a) The Bragg's law relates the wavelength of X-rays to the spacing between the crystal planes and the angle at which the X-rays are incident on the crystal:

nλ = 2d sinθ

where n is an integer representing the order of the diffraction peak, λ is the wavelength of the incident radiation, d is the spacing between the planes, and θ is the angle between the incident X-ray beam and the crystal planes.

In this case, we want to find the wavelength of the electromagnetic waves that give the first strong interference maximum, which corresponds to n=1. The spacing between the planes is given as d = 3.50 Å. The angle of incidence is θ = 15.0 degrees. So we can rearrange the Bragg's law to solve for λ:

λ = 2d sinθ / n = 2(3.50 Å) sin(15.0°) / 1

λ = 1.05 Å

Therefore, the wavelength of the electromagnetic waves needed for the first strong interference maximum in the Bragg reflection is 1.05 Å.

(a2) The wavelength of 1.05 Å corresponds to X-rays, which lie in the X-ray part of the electromagnetic spectrum.

(a3) The other strong interference maxima will occur at angles that satisfy the Bragg's law, i.e.,

nλ = 2d sinθ

For the first maximum (n=1), we found that θ = 15.0°. For higher maxima, we need to find the angles that satisfy this equation for larger values of n. For example, for n=2:

2λ = 2d sinθ

sinθ = λ / 2d = 1.05 Å / (2 × 3.50 Å) = 0.150

θ = sin⁻¹(0.150) = 9.0°

So the second strong interference maximum occurs at an angle of 9.0°. We can repeat this process to find the angles for other maxima.

Know more about  electromagnetic waves   here:

https://brainly.com/question/24319848

#SPJ11

The bullet will be pushed upwards, so the correct option is Up.

When the negatively charged teflon bullet is fired to the west, it will experience a force due to the Earth's magnetic field. This force is determined by the right-hand rule, which states that when you point your thumb in the direction of the velocity vector (west), and your fingers in the direction of the magnetic field lines (north), the force experienced by a negatively charged particle is in the direction of your palm. In this case, the force will be pointing upwards.

As the negatively charged teflon bullet is fired to the west parallel to the ground, it will be pushed upwards by the Earth's magnetic field.

To know more about magnetic field, click here

https://brainly.com/question/14848188

#SPJ11

a. The specific heat of the sample is approximately 0.803 J/g°C.

b. Since the specific heat of the unknown substance is much lower than that of water and higher than that of metals, it is likely a non-metallic substance.

a. To determine the specific heat of the sample, we can use the formula:

Q = mcΔT

where Q is the energy released, m is the mass of the sample, c is the specific heat, and ΔT is the change in temperature.

Substituting the given values, we get:

963.6 J = (120.0 g) c (80.0°C - 90.0°C)

Simplifying the equation, we get:

c = 963.6 J / (120.0 g * 10.0°C)

c ≈ 0.803 J/g°C

b. To identify the substance, we can compare its specific heat to the specific heats of known substances. Here are some common substances and their specific heats:

Water: 4.184 J/g°C

Aluminum: 0.900 J/g°C

Iron: 0.449 J/g°C

Copper: 0.385 J/g°C

Since the specific heat of the unknown substance is much lower than that of water and higher than that of metals, it is likely a non-metallic substance.

For more question on specific heat click on

https://brainly.com/question/21406849

#SPJ11

The specific heat of the unknown substance is 1.61 J/g°C. The substance is most likely water.

To calculate the specific heat of the unknown substance, we can use the formula Q = mcΔT, where Q is the energy released, m is the mass of the substance, c is the specific heat, and ΔT is the change in temperature. Rearranging this formula to solve for c, we get c = Q/(mΔT). Substituting the given values, we get c = 963.6 J/(120.0 g × 10.0°C) = 1.61 J/g°C.

Water has a specific heat of 4.18 J/g°C, which is much higher than the specific heat of the unknown substance. This suggests that the unknown substance is not water. Looking at the table of specific heats for various substances, we can see that the specific heat of aluminum (0.90 J/g°C) and copper (0.39 J/g°C) are much lower than the specific heat of the unknown substance, so they can be ruled out. The specific heat of ethanol (2.44 J/g°C) is closer to the specific heat of the unknown substance, but still higher. Therefore, the unknown substance is most likely water, which has a specific heat of 4.18 J/g°C.

Learn more about specific heat :

https://brainly.com/question/21041726

#SPJ11

The original far point of the patient is 2.2cm

The power of a lens is defined as the reciprocal of its focal length. It is represented by the letter P.

The power P of a lens of focal length f (in m) is given by. P=1/f. The SI unit of power of a lens is 'dioptre'.

If the minimum power for normal vision is 50diopters

Then the focal length of the eye lens = 1/50 = 0.02m

If the minimum power of the patient is reduced by 4.75

= 50-4.75 = 45.25 diopters

the original focal length = 1/45.25

= 0.022m = 2.2 cm

learn more about power of lens from

https://brainly.com/question/30995178

#SPJ4

The magnitude of the force on each electron in the magnetic field is 1.68 x 10^-17 N.

To find the force on each electron, we can use the formula F = qvBsinθ, where F is the force, q is the charge of an electron, v is the velocity of the electron, B is the magnetic field, and θ is the angle between the velocity and magnetic field. Given that the angle is 90° (right angles), sin90° = 1.

1. The charge of an electron (q) = -1.6 x 10^-19 C
2. The velocity of the electron (v) = 2.5 x 10^6 m/s
3. The magnetic field (B) = 3.0 x 10^-2 T

Now, plug these values into the formula: F = (-1.6 x 10^-19 C) x (2.5 x 10^6 m/s) x (3.0 x 10^-2 T) x sin(90°)
F = (-1.6 x 10^-19 C) x (2.5 x 10^6 m/s) x (3.0 x 10^-2 T) x 1
F ≈ -1.68 x 10^-17 N
Since we're asked for the magnitude, we take the absolute value, which is 1.68 x 10^-17 N.

Learn more about magnetic field here:

https://brainly.com/question/23096032

#SPJ11

Three capacitors with capacitance values of 8.0 μf, 11 μf, and 16 μf are connected in parallel. The equivalent capacitance is calculated by adding up the individual capacitances, resulting in a total of 35 μf.

When capacitors are connected in parallel, the equivalent capacitance is equal to the sum of individual capacitances. Therefore, to find the equivalent capacitance of the given capacitors, we simply add their capacitance values.

C_eq = C_1 + C_2 + C_3

C_eq = 8.0 μF + 11 μF + 16 μF

C_eq = 35 μF

The equivalent capacitance of the three capacitors connected in parallel is 35 μF.

In parallel connection, the positive plate of all capacitors is connected together and the negative plate of all capacitors is also connected together. When capacitors are connected in parallel, the voltage across each capacitor is the same and equal to the voltage across the entire circuit. The total capacitance of the circuit is increased, which results in an increase in the amount of charge that can be stored in the circuit.

In practical applications, capacitors are often connected in parallel to increase the capacitance of a circuit. For example, in an audio system, capacitors are used to filter out unwanted noise from the signal. By connecting multiple capacitors in parallel, the amount of noise that can be filtered out is increased, resulting in a cleaner audio signal.

To know more about the capacitors refer here :

https://brainly.com/question/17176550#

#SPJ11

A series circuit is a simple circuit that consists of one path for the current to flow through.

According to the Ohm's Law, A series circuit is a type of circuit where the components are connected in a line, one after the other. In this type of circuit, the current flows through each component in sequence, meaning that the current passing through each component is the same.

This is because there is only one path for the current to flow through, and the resistance of each component adds up to create a total resistance for the circuit.

In a series circuit, if one component fails, the entire circuit will fail. This is because the current is unable to flow past the failed component, and the circuit becomes open. Additionally, the voltage is divided across each component in the circuit, meaning that the voltage across each component is proportional to its resistance.

Learn more about Ohm's Law

brainly.com/question/1247379

#SPJ11

The final enthalpy of the steam is 2,670.2 kJ/kg  at 500 kpa and 300°c expands is entropically to 50 kpa .

To solve this problem, we can use the steam tables to find the initial and final enthalpies of the superheated steam.

From the steam tables, we can find that the initial enthalpy of superheated steam at 500 kPa and 300°C is 3,107.6 kJ/kg. To find the final enthalpy of the steam at 50 kPa, we need to know the quality of the steam at this pressure. If the steam is still superheated, then we can use the steam tables to find the enthalpy of superheated steam at 50 kPa and the same temperature as before (300°C). If the steam has undergone a phase change to saturated vapor or a mixture of vapor and liquid, then we need to use a different method to find the final enthalpy.

Assuming that the steam remains superheated, we can find from the steam tables that the enthalpy of superheated steam at 50 kPa and 300°C is 2,670.2 kJ/kg.

Therefore, the final enthalpy of the steam is 2,670.2 kJ/kg.

To know more about enthalpy refer here :

https://brainly.com/question/31481062

#SPJ11

To prepare a tungsten wire with a resistance of 2.27 kΩ and a diameter of 0.137 mm, the wire must be 5.96 m long. The resistivity of tungsten is 5.62×10⁻⁸ Ω·m.

The formula for resistance is:

R = (ρ * L) / A

Where R is the resistance, ρ is the resistivity, L is the length, and A is the cross-sectional area of the wire.

We can rearrange this formula to solve for L:

L = (R * A) / ρ

The diameter of the wire is 0.137 mm, which means the radius is 0.0685 mm or 6.85×10⁻⁵ m. The cross-sectional area can be calculated as:

A = π * r² = 3.14 * (6.85×10⁻⁵ m)² = 1.48×10⁻⁸ m²

Substituting the given values into the formula for length, we get:

L = (2.27×10³ Ω * 1.48×10⁻⁸ m²) / (5.62×10⁻⁸ Ω·m) = 5.96 m

Therefore, the length of the tungsten wire needed to have a resistance of 2.27 kΩ and a diameter of 0.137 mm is approximately 5.96 meters.

To know more about the tungsten wire refer here :

https://brainly.com/question/9323291#

#SPJ11