An L-R-C series circuit consists of a 2.50 uF capacitor, a 4.50 mH inductor, and a 60.0 ohm resistor connected across an ac source of voltage amplitude 18.0 V having variable frequency.
(a)At what frequency is the average power delivered to the circuit equal to 1/2 V_rms I_rms ?

Answers

Answer 1

The frequency at which the average power delivered to the circuit is equal to 1/2 V_rms I_rms is approximately 1.33 kHz.

The average power delivered to an L-R-C series circuit is given by the equation P_avg = 1/2 V_rms I_rms cos(phi), where phi is the phase angle between the voltage and current. At resonance, the phase angle is zero and cos(phi) = 1, so the average power is simply equal to V_rms I_rms. The resonant frequency of an L-R-C series circuit can be calculated using the equation f_res = 1/(2pisqrt(LC)), where L is the inductance, C is the capacitance, and pi is the mathematical constant pi (approximately 3.14159). Substituting the given values, we get f_res = 1/(2pisqrt(2.50e-64.50e-3)) = 1.33 kHz (approximately). Therefore, at a frequency of 1.33 kHz, the average power delivered to the circuit is equal to 1/2 V_rms I_rms.

To know more about frequency, click here:

https://brainly.com/question/29739263

#SPJ11


Related Questions

the area of 20 ft^2 of a wooden board may be used to build a box. the base of the box must be a rectangle whose ratio of the sides is 2:3. what are the dimensions of the box that maximize its volume?

Answers

The dimensions of the box that maximize its volume 20.84 cubic feet..

Let the dimensions of the rectangle be 2x and 3x, so the area of the rectangle is:

2x * 3x = [tex]6x^2[/tex]

We know that the area of the board is 20 sq ft, so:

[tex]6x^2[/tex] = 20

Solving for x, we get:

x = sqrt(20/6) = 1.825

So the dimensions of the rectangle are:

2x = 3.65 ft (width)

3x = 5.475 ft (length)

To maximize the volume, we need to make the height of the box as large as possible, subject to the constraint that the area of the board is 20 sq ft. Let h be the height of the box.

The volume of the box is given by:

V = (2x)(3x)(h) = [tex]6x^2h[/tex]

Substituting x = 1.825, we get:

V = 6(1.825)[tex]^2h[/tex] = 20.84h

To maximize V subject to the constraint that the area of the board is 20 sq ft, we use the area formula to solve for h:

(2x)(3x) + 2(2x)(h) + 2(3x)(h) = 20

Simplifying and solving for h, we get:

h = (20 -[tex]6x^2[/tex]) / (4x) = (20 - 6(1.825)^2) / (4(1.825)) = 2.416 ft

Therefore, the dimensions of the box that maximize its volume are:

Width = 3.65 ft

Length = 5.475 ft

Height = 2.416 ft

And the maximum volume of the box is: V = 20.84 cubic feet.

Therefore, 20.84 cubic feet is the dimensions of the box that maximize its volume.

To know more about Volume refer here :

https://brainly.com/question/14197390

#SPJ11

If the rest energies of a proton and a neutron (the two constituents of nuclei) are 938.3 and 939.6 MeV respectively, what is the difference in their masses in kilograms?

Answers

To find the difference in masses between a proton and a neutron, we need to convert their rest energies from MeV (mega-electron volts) to kilograms using the equation E = mc², where E is the rest energy, m is the mass, and c is the speed of light.

Given:

Rest energy of a proton (Ep) = 938.3 MeV

Rest energy of a neutron (En) = 939.6 MeV

Converting MeV to joules:

1 MeV = 1.602 × 10^(-13) joules

Rest energy of a proton (Ep) in joules:

Ep_joules = 938.3 MeV * (1.602 × 10^(-13) joules/1 MeV)

Ep_joules = 1.503 × 10^(-10) joules

Rest energy of a neutron (En) in joules:

En_joules = 939.6 MeV * (1.602 × 10^(-13) joules/1 MeV)

En_joules = 1.505 × 10^(-10) joules

Now, we can use the equation E = mc² to find the mass (m) for each particle:

For the proton:

Ep_joules = mp * c², where mp is the mass of the proton

Solving for mp:

mp = Ep_joules / c²

For the neutron:

En_joules = mn * c², where mn is the mass of the neutron

Solving for mn:

mn = En_joules / c²

We know that the speed of light, c, is approximately 2.998 × 10^8 m/s.

Calculating the mass of the proton (mp):

mp = Ep_joules / c²

mp = (1.503 × 10^(-10) joules) / (2.998 × 10^8 m/s)²

Calculating the mass of the neutron (mn):

mn = En_joules / c²

mn = (1.505 × 10^(-10) joules) / (2.998 × 10^8 m/s)²

Simplifying:

mp ≈ 1.67262192 × 10^(-27) kg

mn ≈ 1.67492747 × 10^(-27) kg

The mass difference between a proton and a neutron is:

Δm = mn - mp

Δm ≈ (1.67492747 × 10^(-27) kg) - (1.67262192 × 10^(-27) kg)

Δm ≈ 2.30555 × 10^(-30) kg

Therefore, the difference in masses between a proton and a neutron is approximately 2.30555 × 10^(-30) kg.

To know more about energies refer here

https://brainly.com/question/1932868#

#SPJ11

if an electromagnetic wave has components ey=e0sin(kx−ωt) and bz=b0sin(kx−ωt), in what direction is it traveling?

Answers

If an electromagnetic wave has Components Ey = E0sin(kx - ωt) and Bz = B0sin(kx - ωt), it is traveling in the x-direction.


1. Identify the given components of the electromagnetic wave: Ey and Bz.
2. Notice that both components have the same sinusoidal form (sin(kx - ωt)), indicating they are in phase.
3. Recall that electromagnetic waves have electric and magnetic field components that are perpendicular to each other and to the direction of wave propagation.
4. Since the electric field component (Ey) is in the y-direction and the magnetic field component (Bz) is in the z-direction, the wave must be propagating in the x-direction, perpendicular to both the y and z directions.

To know more about  electromagnetic wave components refer https://brainly.com/question/25847009

#SPJ11

a current of 4.91 a is passed through a cu(no3)2 solution. how long, in hours, would this current have to be applied to plate out 8.40 g of copper?

Answers

The current of 4.91 A would need to be applied for 1.44 hours to plate out 8.40 g of copper, using the equation Q = I * t.

How does the efficiency of electroplating process affect results?

The amount of copper of electroplating that can be plated out from the Cu(NO3)2 solution depends on the amount of charge passed through the solution, which is directly proportional to the current and the time for which it is applied. The equation that relates the amount of charge passed (Q), the current (I), and the time (t) is Q = I * t.

To calculate the time required to plate out 8.40 g of copper, we need to first calculate the amount of charge required. The molar mass of Cu is 63.55 g/mol, which means that 8.40 g of copper is equivalent to 8.40/63.55 = 0.132 mol of copper. Each copper ion (Cu2+) requires 2 electrons to be reduced to copper metal. Therefore, the amount of charge required to plate out 0.132 mol of copper is:

Q = 2 * 0.132 * 96500 = 25452 C

where 96500 is the Faraday constant.

Now, we can use the equation Q = I * t to calculate the time required to pass this amount of charge at a current of 4.91 A:

t = Q / I = 25452 / 4.91 = 5189 s = 1.44 hours

Therefore, the current of 4.91 A would need to be applied for 1.44 hours to plate out 8.40 g of copper.

It's worth noting that this calculation assumes 100% efficiency in the electroplating process, which is often not the case in practice. Factors such as the purity of the solution, the temperature, and the electrode surface area can all affect the efficiency of the electroplating process and should be taken into account in real-world applications.

Learn more about electroplating

brainly.com/question/20112817

#SPJ11

If tight scissors have an efficiency of 50 percent, half of your work is wasted due to _____________________

Answers

If tight scissors have an efficiency of 50 percent, half of your work is wasted due to mechanical losses or inefficiencies.

Efficiency is a measure of how effectively a device or system converts input energy into useful output energy. In this case, the efficiency of tight scissors being 50 percent means that only half of the input energy you apply to the scissors is converted into useful output energy, while the other half is lost due to various factors.

Mechanical losses or inefficiencies in scissors can occur for several reasons, including friction, imperfect cutting edges, and deformation of the materials. When you squeeze the handles of the scissors, the energy you apply is not entirely transferred to the cutting action. Some of the energy is dissipated as heat due to friction between the blades, pivot point, and other moving parts. Additionally, if the scissors have dulled or damaged edges, more energy is required to cut through materials, resulting in increased inefficiency.

The wasted energy that is not utilized for cutting is typically converted into heat or sound energy, which does not contribute to the desired output of the scissors.

Therefore, due to mechanical losses or inefficiencies in the scissors, half of the work you apply is wasted, resulting in a 50 percent efficiency. This means that only half of your effort is effectively utilized for cutting, while the other half is lost as non-useful energy.

To know more about mechanical losses, please click on:

https://brainly.com/question/31722909

#SPJ11

EURASIA EUROPE NORTH AMERICA ASIA & OCEANIA MIDDLE AFRICA CENTRAL & SOUTH AMERICA COAL NATURAL GAS OIL Africa 8961 Middle Mid
Based on U.S. Department of Energy Information Administration (EIA) data.
For example, 62% of the United States’ energy comes from petroleum and natural gas. The majority of these proven energy reserves are not, however, found in North America.
Fortunately, this dependence on other countries for energy is not as crucial with respect to coal reserves. That is, North America holds of the world’s coal reserves, essentially matching for the leading volume of coal reserves in the world.
A solid fossil fuel formed from ancient plant material, coal is, by far, the most abundant and fossil fuel in use today.
As a result, coal use has caused a plethora of environmental and health concerns. For example, it increases air pollution by emitting carbon dioxide and into the atmosphere. Burning coal can thus increase rates of respiratory illnesses for people who live near coal power plants and damage the local environment with toxic chemicals.
Which of the following will likely discourage the use of coal and possibly mitigate the environmental and health concerns that coal causes? Check all that apply.
Include the effects of air and water pollution in the market price of using coal.
Support the Clean Coal campaign.
Classify coal ash as hazardous waste.

Answers

Including the environmental and health impacts of coal in its market price and classifying coal ash as hazardous waste.

How can coal usage be discouraged and its environmental impact reduced?

Including the effects of air and water pollution in the market price of using coal would mean that the true cost of coal would reflect the environmental and health damages caused by its use. By internalizing these external costs, coal would become more expensive compared to cleaner energy sources, making them more economically attractive. This would incentivize the shift towards cleaner alternatives, leading to a decrease in coal consumption.

Classifying coal ash as hazardous waste would impose stricter regulations on its handling and disposal. Currently, coal ash contains various toxic substances that can contaminate water sources and pose risks to human health and the environment. By designating coal ash as hazardous waste, stricter standards for storage and disposal would be enforced, reducing the potential for water pollution and associated health hazards.

Learn more about environmental

brainly.com/question/21976584

#SPJ11

When charging, which type of material usually gives off electrons: conductors or insulators? Why?



I need answers asaaap

Answers

When charging, conductors usually give off electrons. Conductors are materials that allow electrons to pass through them easily, whereas insulators are materials that prevent electrons from moving through them. Conductors can easily discharge when exposed to static electricity because electrons move more freely through conductors than they do through insulators.

When an object with an excess of electrons comes into touch with an object with a deficiency of electrons, the electrons will move from the charged object to the uncharged object because of the difference in potential energy. The most familiar conductors are metals, which are highly conductive due to the presence of free electrons. Insulators, on the other hand, are materials that do not conduct electricity. Air, paper, plastic, and rubber are all examples of insulators. The transfer of electrons from one object to another by friction, conduction, or induction is referred to as charging. When two materials are rubbed together, their electrons rub together, resulting in one material becoming charged positively and the other becoming charged negatively.

Learn more about potential energy here ;

https://brainly.com/question/24284560

#SPJ11

Dominique is given a bowling ball and informed that the ball is solid (not hollow) and is made of the same material throughout. Her online research indicates, however, that most bowling balls have materials of different densities in their core. Further research indicates that a solid sphere of mass M and radius R having uniform density has a rotational inertia I = 0.4MR. Dominique decides to experimentally measure the bowling ball's rotational inertia. PART A: Dominique has access to a ramp, a meterstick, a stopwatch, an electronic balance, and several textbooks. In the space below, outline a procedure that she could follow to make measurements that can be used to determine the rotational inertia of the bowling ball. Give each measurement a meaningful algebraic symbol and be sure to explain how each piece of equipment is being used.

Answers

The electronic balance is used to measure the mass of the ball, the meterstick is used to measure the radius of the ball, the ramp is used to provide a means for the ball to roll down without slipping, and the stopwatch is used to measure the time it takes for the ball to travel down the ramp.

Procedure to measure the rotational inertia of the bowling ball

1. Measure the mass of the bowling ball using an electronic balance and denote it as M.

2. Measure the radius of the bowling ball using a meterstick and denote it as R.

3. Set up the ramp at an angle such that the ball will roll down without slipping. Measure the height of the ramp and denote it as h.

4. Place the bowling ball at the top of the ramp and release it. Measure the time it takes for the ball to reach the bottom of the ramp using a stopwatch and denote it as t.

5. Using the equations of motion for rolling without slipping, calculate the linear speed of the bowling ball at the bottom of the ramp. Denote it as v.

6. Using the rotational motion equations, calculate the rotational inertia of the bowling ball. Denote it as I.

I = (2/5) M [tex]R^{2}[/tex] + M [tex]v^{2}[/tex] / [tex]R^{2}[/tex]

7. Repeat the experiment multiple times and take the average of the calculated values of I to minimize errors.

In this procedure, the electronic balance is used to measure the mass of the ball, the meterstick is used to measure the radius of the ball, the ramp is used to provide a means for the ball to roll down without slipping, and the stopwatch is used to measure the time it takes for the ball to travel down the ramp. The textbooks are not directly used in the procedure but could be used to assist in understanding the concepts and equations involved.

To know more about meterstick here

https://brainly.com/question/1209224

#SPJ4

the diode laser keychain you use to entertain your cat has a wavelength of 655 nmnm . if the laser emits 3.70×1017 photons during a 30.0 ss feline play session, what is its average power output

Answers

The average power output of the laser during the 30.0 s feline play session is 3.74 x 10⁻³ W.

The average power output of the laser can be calculated using the formula:

Power = Energy/Time

where Energy is the total energy emitted by the laser during the play session, and Time is the duration of the play session.

The energy emitted by each photon of the laser can be calculated using the formula:

Energy = h*c/λ

where h is Planck's constant, c is the speed of light, and λ is the wavelength of the laser.

Substituting the given values, we get:

Energy per photon = (6.626 x 10⁻³⁴ J s) x (2.998 x 10⁸ m/s) / (655 x 10⁻⁹ m)

= 3.033 x 10⁻¹⁹ J

The total energy emitted by the laser during the 30.0 s play session can be calculated by multiplying the energy per photon by the number of photons emitted:

Total energy = Energy per photon x Number of photons emitted

= (3.033 x 10⁻¹⁹ J/photon) x (3.70 x 10¹⁷ photons)

= 1.122 x 10⁻¹ J

Finally, we can calculate the average power output of the laser during the play session:

Power = Energy/Time

= (1.122 x 10⁻¹ J) / (30.0 s)

= 3.74 x 10⁻³ W

Therefore, the average power output of the laser during the 30.0 s feline play session is 3.74 x 10⁻³ W.

Note: The power output of a laser is the rate at which it emits energy in the form of photons. The energy of each photon is determined by its frequency or wavelength. In this case, the laser emits photons with a wavelength of 655 nm, and the number of photons emitted is given. From this information, we can calculate the total energy emitted and then the power output.

To know more about power output, refer to the link below:

https://brainly.com/question/31961373#

#SPJ11

what are the first three overtones of a double reed instrument that has a fundamental frequency of 118 hz? it is open at both ends.

Answers

The first three overtones of a double reed instrument with a fundamental frequency of 118 Hz that is open at both ends are 236 Hz, 354 Hz, and 472 Hz.

The frequency of the first overtone is two times the frequency of the fundamental, which gives us 236 Hz 118 Hz x 2 = 236 Hz The frequency of the second overtone is three times the frequency of the fundamental, which gives us 354 Hz 118 Hz x 3 = 354 Hz. The frequency of the third overtone is four times the frequency of the fundamental, which gives us 472 Hz 118 Hz x 4 = 472 Hz.

The first three overtones of this double reed instrument are 236 Hz, 354 Hz, and 472 Hz. Explanation: An open-ended instrument has its overtones at integer multiples of the fundamental frequency. Determine the fundamental frequency: 118 Hz. Calculate the first overtone by multiplying the fundamental frequency by 2: 118 Hz x 2 = 236 Hz. Calculate the second overtone by multiplying the fundamental frequency by 3: 118 Hz x 3 = 354 Hz Calculate the third overtone by multiplying the fundamental frequency by 4: 118 Hz x 4 = 472 Hz.

To know more about frequency visit:

https://brainly.com/question/2140860

#SPJ11

A cube of a certain metal has 0.040 m sides and its mass is 0.48 kg. What is the mass density of the cube?a. 8700 kg/m3 b. 1800 kg/m3 c. 3000 kg/m3 d. 1200 kg/m3 e. 7500 kg/m3

Answers

The mass density of a cube of a certain metal with 0.040 m sides and a mass of 0.48 kg is calculated by dividing the mass of the cube by the volume of the cube. The mass density is (e) 7500 kg/m³.

To find the mass density of the cube, we can use the formula:

mass density = mass / volume

Since the cube has equal sides of 0.040 m, its volume is given by:

volume = length × width × height = 0.040 m × 0.040 m × 0.040 m = 0.000064 m³

We know the mass of the cube is 0.48 kg, so we can now calculate the mass density:

mass density = 0.48 kg / 0.000064 m³ = 7500 kg/m³

Therefore, the mass density of the cube is 7500 kg/m³, and the correct answer is (e).

To know more about the mass density refer here :

https://brainly.com/question/6107689#

#SPJ11

calculate the approximate random error ∆h = (1/2) [h(max) - h(min)], where h(max) and h(min) are the highest and lowest values of h. ∆h refers to the random error in each measurement of h.

Answers

According to the given statement, the approximate random error in a measurement of h is ∆h = (1/2) [h(max) - h(min)].

To calculate the approximate random error ∆h, we need to first find the highest and lowest values of h, denoted by h(max) and h(min), respectively. Once we have these values, we can use the formula: ∆h = (1/2) [h(max) - h(min)] to calculate the approximate random error.
\The term "random error" refers to the uncertainty or variability in a measurement that arises from factors such as instrument imprecision, observer bias, or environmental fluctuations. This type of error is different from systematic error, which results from a consistent bias in measurement.
By calculating the random error in each measurement of h, we can determine the range of values within which the true value of h is likely to lie. This information is important for assessing the reliability and accuracy of our measurements and for making informed decisions based on the data.
In summary, the formula for calculating the approximate random error in a measurement of h is ∆h = (1/2) [h(max) - h(min)]. This value reflects the uncertainty and variability inherent in the measurement and provides important information for evaluating the quality of our data.

To know more about measurement visit:

brainly.com/question/31404742

#SPJ11

Matching- Active Galaxies. Match the terms to the description which best fits it. Answers may be used more than once or not at all. See the AGN lecture for terms not found in your textbook chapter 27.Regions near the core of a galaxy that are abnormally bright in some wavelengthPossible Answers for Matching 1: AGN, quasar, blazaar, SMBH, radio galaxy
Galaxy formation and evolution seems to be a combination of which two processes?
(Early cloud collapse / later stellar collisions / later galaxy mergers / early stellar accretion)
How have astronomers ruled out the idea that dark matter is simply massive, dark objects in the halo of galaxies?

Answers

Matching 1:

- Regions near the core of a galaxy that are abnormally bright in some wavelength: AGN

Matching 2:

- Galaxy formation and evolution seems to be a combination of which two processes?: Early cloud collapse and later galaxy mergers

Regarding the question about ruling out the idea of dark matter being massive, dark objects in the halo of galaxies, astronomers have used various methods to investigate and understand dark matter. One of the key reasons that dark matter is believed to be something other than massive, dark objects in the halo of galaxies is the observation of gravitational lensing. Gravitational lensing occurs when the gravitational field of a massive object bends and distorts light passing near it. By studying gravitational lensing in galaxies and galaxy clusters, astronomers have found evidence for the presence of dark matter, as the observed gravitational effects are much larger than what could be explained by visible matter alone. Additionally, other observations such as the rotation curves of galaxies and the distribution of matter in galaxy clusters also support the existence of dark matter as a distinct entity from ordinary matter.

Learn more about **dark matter** and the evidence supporting its existence here:

https://brainly.com/question/29545146?referrer=searchResults

#SPJ11

The position of a 0.30-kg object attached to a spring is described by x = (0.30 m) cos(0.8?t). (a) Find the amplitude of the motion. m (b) Find the spring constant. (c) Find the position of the object at t = 0.29 s. m (d) Find the object's speed at t = 0.29 s. m/s

Answers

The position of a 0.30-kg object which is attached to a spring is described by x = (0.30 m) cos(0.8?t). Then, the amplitude of the motion is; 0.30 m, the spring constant is 0.192 N/m, the position of the object at t = 0.29 s is 0.260 m, and the object's speed is 0.070 m/s when t = 0.29 s .

The amplitude of the motion is the maximum displacement from equilibrium, which is equal to the coefficient in front of the cosine function. Therefore, the amplitude is 0.30 m.

The equation of motion for a mass attached to a spring is given by:

x = A cos(ωt)

where x is position of the mass, A is amplitude, ω is angular frequency, and t is time. The spring constant, k, is related to angular frequency by the equation;

ω = √(k/m)

where m is the mass of the object attached to the spring.

Rearranging this equation to solve for k, we get;

k = mω²

Plugging in the given values, we get;

k = (0.30 kg)(0.8 rad/s)² = 0.192 N/m

Therefore, the spring constant is 0.192 N/m.

To find the position of the object at t = 0.29 s, we plug in the given value of t into the equation for x;

x = (0.30 m) cos(0.8?t)

x = (0.30 m) cos(0.8 × 0.29 s)

x = 0.260 m

Therefore, the position of the object at t = 0.29 s is 0.260 m.

The velocity of the object is given by the derivative of the position function with respect to time;

v = dx/dt = -Aω sin(ωt)

At t = 0.29 s, we have;

v = -(0.30 m)(0.8 rad/s) sin(0.8 × 0.29 s)

v = -0.070 m/s

Therefore, the object's speed at t = 0.29 s is 0.070 m/s.

To know more about spring constant here

https://brainly.com/question/20785296

#SPJ4

A block of ice atImage for A block of ice at0 degree C is floating on the surface of icewater in a beaker. The surface of the water justis floating on the surface of icewater in a beaker. The surface of the water just comes to the topof the beaker. When the ice melts the water level will:
A. rise and overflow will occur
B. remain the same
C. fall
D. depend on the initial ratio of water to ice
E. depend on the shape of the block of ice

Answers

When the block of ice at 0°C melts in a beaker of ice water, the water level in the beaker will remain the same. This is because the volume of ice that is submerged in the water is equal to the volume of water displaced by the ice, and when the ice melts, it turns into water which occupies the same volume.

The correct option is  (B).

The mass of the ice is equal to the mass of the water it displaces, and since ice has a lower density than water, the volume of ice that is submerged in water is equal to the volume of water displaced by the ice.

When the ice melts, the water formed has the same volume as the ice, and hence the water level in the beaker remains the same.

To know more about volume refer here :-

https://brainly.com/question/1578538#

#SPJ11

as magnifying power increases the microscope's depth of focus decreasesT/F

Answers

True. As the magnifying power of a microscope increases, the depth of focus decreases. Depth of focus refers to the range of depth that appears in sharp focus at any given point.

It is influenced by various factors, including the wavelength of light and the numerical aperture of the lens system. When a microscope is used to view a specimen at higher magnification, the depth of field becomes more shallow, meaning that only a small portion of the sample can be in focus at any given time.

This can make it more difficult to obtain a clear, detailed image of the entire specimen. To compensate for this, microscopists may use techniques such as adjusting the aperture or using a technique known as "stacking" to combine multiple images taken at different focal points. Overall, the relationship between magnifying power and depth of focus is an important consideration when selecting the appropriate microscope for a particular application.

to know more about magnifying power click this link

brainly.com/question/31475644

#SPJ11

In the sport of horseshoe pitching, two stakes are 40. 0 feet apart. What is the distance in meters between the two stakes? *

Answers

The distance between the two stakes in horseshoe pitching is approximately 12.192 meters.

The given problem states that the two stakes in horseshoe pitching are 40 feet apart. And we are supposed to find out the distance between them in meters. Let us first write down the given value in feet.Given that the distance between the two stakes is 40 feet. Now, 1 meter is equivalent to 3.28084 feet.To convert feet into meters, we need to divide the given value of feet by the value of 3.28084.Thus, the distance between the two stakes in meters can be calculated as follows: Distance in meters = \frac{distance in feet }{ 3.28084 }

.Distance in meters =\frac{ 40 }{ 3.28084 meters} ≈ 12.192 meters.

Therefore, the distance between the two stakes in horseshoe pitching is approximately 12.192 meters. The exact value can be obtained by using more number of decimal points.

learn more about distance Refer: https://brainly.com/question/30195100

#SPJ11

you plan to cold work a cylindrical rod of 1040 steel from a diameter of 10mm to a diameter of 9mm in one step. what is the final yield strength

Answers

The final yield strength of the cold-worked 1040 steel rod is approximately 750 MPa. If a cylindrical rod of 1040 steel from a diameter of 10mm to a diameter of 9mm in one step.

When cold working a cylindrical rod of 1040 steel from an initial diameter of 10mm to a final diameter of 9mm, you'll need to determine the final yield strength.

To calculate the final yield strength, you should first find the percentage of cold work (%CW) using the formula:

%CW = [(Initial Area - Final Area) / Initial Area] x 100

The area of a circle is given by the formula A = πr², where r is the radius.

Initial Area = π(5mm)² = 78.54mm²
Final Area = π(4.5mm)² = 63.62mm²

%CW = [(78.54 - 63.62) / 78.54] x 100 = 19.0%

Next, refer to a table or chart to find the relationship between %CW and the increase in yield strength for 1040 steel. Let's assume that a 19% cold work results in a 200 MPa increase in yield strength. Now, find the initial yield strength of 1040 steel, which is approximately 550 MPa.


Final Yield Strength = Initial Yield Strength + Increase in Yield Strength
Final Yield Strength = 550 MPa + 200 MPa = 750 MPa

To know more about  final yield strength visit:-

https://brainly.com/question/30850704

#SPJ11

Balloon a is ___ charged and balloon c is ___ charged. If balloon a approaches balloon c there will be a force of blank between them

Answers

Balloon A is positively charged, and balloon C is negatively charged. If balloon A approaches balloon C, there will be an electrostatic force of attraction between them.

When two objects carry opposite charges, they exert an attractive force on each other. This force is known as the electrostatic force and follows Coulomb's law. According to Coulomb's law, the magnitude of the electrostatic force between two charged objects is directly proportional to the product of their charges and inversely proportional to the square of the distance between them. In this scenario, since balloon A is positively charged and balloon C is negatively charged, they have opposite charges. Therefore, the electrostatic force between them will be attractive. The magnitude of the force depends on the charges of the balloons and the distance between them. It is important to note that without specific information about the charges of the balloons and their distance, it is not possible to determine the exact magnitude of the force. To calculate the force, you would need the values of the charges and the distance between the balloons.

For such more questions on electrostatic

https://brainly.com/question/30388162

#SPJ11

calculate the wavelength (in nm) of the blue light emitted by a mercury lamp with a frequency of 6.88 × 1014 s-1.

Answers

The wavelength of the blue light emitted by a mercury lamp with a frequency of[tex]6.88 × 10^14 s^-1[/tex] is 436.6 nm.

The wavelength of the blue light emitted by the mercury lamp can be calculated using the equation λ = c/ν, where λ is the wavelength, c is the speed of light ([tex]3.00 × 10^8 m/s[/tex]), and ν is the frequency of the light. First, the frequency of the light is converted to hertz by multiplying 6.88 × 10^14 s^-1 by 1 Hz/1 s, giving a frequency of [tex]6.88 × 10^14 Hz[/tex]. Then, the frequency is plugged into the equation,[tex]λ = 3.00 × 10^8 m/s ÷ 6.88 × 10^14 Hz[/tex], and the answer is converted from meters to nanometers by multiplying by [tex]10^9[/tex], resulting in a wavelength of 436.6 nm for the blue light emitted by the mercury lamp.

Learn more about wavelength here:

https://brainly.com/question/31143857

#SPJ11

Construct and Present Arguments You have been asked to join a


debate about the existence of gravity. Develop an argument to support


the idea that gravitational forces are attractive and depend on the mass


of the object. Use evidence to add validity to your argument

Answers

Gravitational forces are attractive and depend on the mass of the objects involved. This is supported by various lines of evidence, such as the observed behavior of celestial bodies, the laws of motion formulated by Isaac Newton, and the predictions and measurements made by Albert Einstein's theory of general relativity.

Gravitational forces being attractive and dependent on the mass of objects can be substantiated by several pieces of evidence. Firstly, the observed behavior of celestial bodies in the universe supports this notion. Planets orbit around stars, moons orbit around planets, and galaxies exhibit cohesive structures. These motions can be explained by the attractive nature of gravity, where massive objects exert a pull on other objects.

Secondly, the laws of motion formulated by Isaac Newton provide additional evidence. Newton's law of universal gravitation states that every particle attracts every other particle with a force that is directly proportional to the product of their masses and inversely proportional to the square of the distance between their centers. This mathematical relationship implies an attractive force that is influenced by the mass of the objects involved.

Furthermore, Albert Einstein's theory of general relativity, which successfully explains gravity as the curvature of spacetime, also supports the idea of attractive gravitational forces. The theory predicts and has been validated by experiments that massive objects, such as the Sun, can bend the path of light, creating gravitational lensing effects. In conclusion, the existence of gravity as an attractive force dependent on the mass of objects is supported by various lines of evidence. The observed behavior of celestial bodies, the laws of motion formulated by Newton, and the predictions and measurements made by Einstein's theory of general relativity all contribute to the validity of this argument.

To learn more about Gravitational forces refer:

https://brainly.com/question/72250

#SPJ11

let r be a total order on set s. prove that the width of r is 1, and the height of r is |s|.

Answers

The width of total order r on set s is 1, and its height is |s|.

To prove that the width of r is 1, we need to show that the distance between any two elements of s in the ordering r is at most 1. Since r is a total order, any two distinct elements of s are comparable, so the distance between them in r is either 0 or 1. If the distance were greater than 1, then there would exist an element x in s that lies strictly between the two elements, contradicting the assumption that r is a total order. Therefore, the width of r is 1.

To prove that the height of r is |s|, we need to show that there exists a chain (i.e., a totally ordered subset) of r with |s| elements. Since r is a total order, every element of s is comparable with every other element. Therefore, we can construct a chain of |s| elements by starting with any element of s and repeatedly adding the next-largest element until all elements have been included. This chain is totally ordered by the transitivity of r, and it has |s| elements by construction. Therefore, the height of r is |s|.

Learn more about distance here :

https://brainly.com/question/15172156

#SPJ11

the magnetic field due to a long straight wire, at a point near it, is inversely proportional to the square of the distance from the wire. (True or False)

Answers

True. According to the inverse square law of magnetism, the strength of the magnetic field produced by a long straight wire decreases in proportion to the square of the distance from the wire. This means that as the distance from the wire increases, the strength of the magnetic field decreases rapidly.

"The magnetic field due to a long straight wire, at a point near it, is inversely proportional to the square of the distance from the wire. (True or False)"

The answer is False. The magnetic field due to a long straight wire at a point near it is inversely proportional to the distance from the wire, not the square of the distance. The formula for the magnetic field B at a distance r from a long straight wire carrying current I is given by B = (μ₀I) / (2πr), where μ₀ is the permeability of free space.

To know more about Magnetism visit:

https://brainly.com/question/2841288

#SPJ11

The resonant frequency of an rlc series circuit is 4.8 ✕ 103 hz. if the self-inductance in the circuit is 5.3 mh, what is the capacitance in the circuit (in µf)?

Answers

The capacitance in the circuit is approximately 1.741 × 10⁻³ µF.

To find the capacitance in the RLC series circuit, we can use the formula for resonant frequency:

f = 1 / (2 * π * √(L * C))

Where f is the resonant frequency, L is the self-inductance, and C is the capacitance. We have f = 4.8 × 10³ Hz and L = 5.3 mH. We need to find C.

Rearranging the formula for C, we get:

C = 1 / (4 * π² * f² * L)

Plugging in the given values:

C = 1 / (4 * π² * (4.8 × 10³)² * (5.3 × 10⁻³))

C ≈ 1.741 × 10⁻⁹ F

Since you want the capacitance in µF, we convert it:

C ≈ 1.741 × 10⁻⁹ F * (10⁶ µF/F) ≈ 1.741 × 10⁻³ µF

So, the capacitance in the circuit is approximately 1.741 × 10⁻³ µF.

To learn more about frequency, refer below:

https://brainly.com/question/5102661

#SPJ11

You dive straight down into a pool of water. You hit the water with a speed of 5.0 m/s, and your mass is 75 kg. Assuming the drag force of the form FD=(−1.10×10^4)V, how long does it take you to reach 2% of your original speed? (Ignore effects of buoyancy.)

Answers

The time required to reach 2% of the original speed in the pool of water is 0.0067 s.

Given:

Speed, v = 5 m/s

Mass, 75 kg

Drag force, F = -1.1 × 10⁴ V

The drag force acting on an object in a fluid is given by the equation:

F = -bv

Here b is the drag coefficient and v is the velocity of the object.

From Newton's second law of motion:

F = ma

(-1.10 × 10⁴)V = m × a

a = (-1.10 × 10⁴ V) / m

Substituting the given values:

a = (-1.10 × 10⁴ × 5.0 m/s) / 75 kg

a = -733.33 m/s²

The time it takes to reach 2% of the original speed:

v = u + at

0.1 m/s = 5.0 m/s + (-733.33 m/s²)  t

-4.9 m/s = -733.33 m/s^2 × t

t = 0.0067 s

Hence, the time is 0.0067 s.

To learn more about time, here:

https://brainly.com/question/28238258

#SPJ12

the size of a filter-drier is based on the following criteria, except _____.

Answers

Answer:

Explanation:

hi

Two lab carts have the same mass and are free to move on a horizontal track. The carts' wheels have negligible mass. Cart 1 travels to the right at 1.0 m/s and collides with cart 2, which is initially at rest, as shown at left above. Cart 2 has a compressed spring-loaded plunger with a nonnegligible amount of stored energy. During the collision, the spring-loaded plunger pops out, staying in contact with cart 1 for 0.10 s as the spring decompresses. Negligible mechanical energy dissipates during the collision. Taking rightward as positive, the carts' velocities after the collision could be which of the following? Select two answers Cart 1 Cart 2 (A)O (B) 0.5 m/s0.5 m/s (C) -0.5 m/s 1.5 m/s (D) -1.0 m/s2.0 m/s

Answers

Carts collide, spring pops out, and decompresses for 0.10 s. Carts' velocities after collision could be -0.5 m/s and 1.5 m/s.


Two lab carts of the same mass with negligible mass wheels are free to move on a horizontal track.

Cart 1 moves to the right at 1.0 m/s and collides with cart 2, which is initially at rest.

Cart 2 has a compressed spring-loaded plunger with stored energy that pops out and stays in contact with cart 1 for 0.10 s as the spring decompresses.

No mechanical energy dissipates during the collision.

The possible velocities after the collision for cart 1 and cart 2 are -0.5 m/s and 1.5 m/s, respectively.

These velocities are determined by the conservation of momentum and the energy stored in the spring.

For more such questions on collide, click on:

https://brainly.com/question/7221794

#SPJ11

The velocities of the two carts after the collision could be 0.5 m/s to the right for Cart 1 and 0.5 m/s to the left for Cart 2, or -1.0 m/s to the left for Cart 1 and 2.0 m/s to the right for Cart 2.

To solve this problem, we can use conservation of momentum. Before the collision, the momentum of the system is the mass of Cart 1 times its velocity, since Cart 2 is initially at rest. During the collision, the spring-loaded plunger transfers some of its stored energy to the carts, causing a change in their velocities. After the collision, the momentum of the system is again the sum of the momenta of the two carts. Since there is no external force acting on the system, the total momentum before and after the collision must be equal.

Using the conservation of momentum, we can set up an equation that relates the velocities of the carts before and after the collision. We know that Cart 1 has a mass of m and an initial velocity of 1.0 m/s to the right, and that Cart 2 has a mass of m and an initial velocity of 0 m/s. Let v1f and v2f be the final velocities of Cart 1 and Cart 2, respectively. The conservation of momentum equation becomes:

(m)(1.0 m/s) + 0 = (m)(v1f) + (m)(v2f)

Simplifying this equation, we get:

v1f + v2f = 1.0 m/s

During the collision, the plunger stays in contact with Cart 1 for 0.10 s as the spring decompresses. Since the collision is elastic, we can use conservation of energy to relate the velocities of the carts before and after the collision. The kinetic energy before the collision is:

KE = (1/2)mv1^2

After the collision, the kinetic energy is:

KE = (1/2)mv1f^2 + (1/2)mv2f^2

Since the plunger transfers energy from the spring to the carts, the total kinetic energy after the collision is greater than the kinetic energy before the collision. We can relate the velocities using the equation:

(1/2)mv1^2 = (1/2)mv1f^2 + (1/2)mv2f^2

Simplifying this equation, we get:

v1^2 = v1f^2 + v2f^2

Substituting v1f + v2f = 1.0 m/s from the conservation of momentum equation, we get

v1^2 = v1f^2 + (1.0 m/s - v1f)^2

Simplifying this equation and solving for v1f, we get:

v1f = (1/2)(1.0 m/s + sqrt(3) m/s)

or

v1f = (1/2)(1.0 m/s - sqrt(3) m/s)

Using these values, we can calculate v2f using the conservation of momentum equation. We get:

v2f = 1.0 m/s - v1f or

v2f = -v1f

Therefore, the possible velocities for Cart 1 and Cart 2 after the collision are 0.5 m/s to the right for Cart 1 and 0.5 m/s to the left for Cart 2, or -1.0 m/s to the left for Cart 1 and 2.0 m/s to the right for Cart 2.

Learn more about conservation of momentum:

https://brainly.com/question/24989124

#SPJ11

Some materials can become strongly magnetized. Which of the following is believed to be the microscopic cause of the macroscopic magnetic field in such materials? A The fields from electrons orbiting the nucleus that behave like current loops. B The fields of the individual electrons due to the property of electron spin. C The fields caused by polarization of the atoms in an electric field. D The fields caused by sharing of electrons in the bonds between atoms

Answers

Some materials can become strongly magnetized. The correct answer is B) The fields of the individual electrons due to the property of electron spin is believed to be the microscopic cause of the macroscopic magnetic field in such materials

In materials that can become strongly magnetized, the macroscopic magnetic field is believed to be caused by the microscopic behavior of electrons and their intrinsic property called "electron spin." Electron spin is not the same as the physical spinning motion of an electron but rather a fundamental quantum property related to its intrinsic angular momentum.

When a material becomes magnetized, it means that the magnetic moments of individual electrons align in a particular direction, creating a net magnetic field. This alignment occurs due to the behavior of electron spins within the material.

The magnetic moment associated with electron spin generates a magnetic field around the electron. In materials that can be magnetized, the collective behavior of these individual electron spins aligns, leading to a net magnetic field that can be observed at the macroscopic level.

The other options listed:

A) The fields from electrons orbiting the nucleus that behave like current loops: While electrons in atoms do have orbital motion around the nucleus, this motion alone does not generate a macroscopic magnetic field. Orbital motion contributes to atomic magnetism but is not the primary cause of the macroscopic magnetic field observed in magnetized materials.

C) The fields caused by polarization of the atoms in an electric field: This refers to electric polarization, not magnetic field generation. Electric polarization occurs when positive and negative charges separate in response to an external electric field, but it does not directly lead to the creation of a macroscopic magnetic field.

D) The fields caused by sharing of electrons in the bonds between atoms: This statement refers to electron sharing in covalent bonds, which is relevant to chemical bonding but not the primary cause of macroscopic magnetic fields.

In summary, the alignment of individual electron spins in materials with strong magnetization is believed to be the microscopic cause of the macroscopic magnetic field observed. This alignment of electron spins leads to a net magnetic moment and gives rise to the magnetic properties of such materials.

To know more about magnetic field, please click on:

https://brainly.com/question/30331791

#SPJ11

A cube of edge length ℓ = 4.00 cm is positioned as shown in the figure below. A uniform magnetic field given by B with arrow = (5.1 î + 4.0 ĵ + 3.0 k) T exists throughout the region. A cube of side ℓ is positioned in the x y z coordinate space, with the +x-axis to the right, the +y-axis upward, and the +z-axis out of the page. One corner of the cube is at the origin, and three edges of the cube lie along the +x-, +y-, and +z-axes. The rightmost face, which is parallel to the y z plane, is shaded. The magnetic field vector B points upward, outward, and to the right. (a) Calculate the magnetic flux through the shaded face. (b) What is the total flux through the six faces?

Answers

The magnetic flux through the shaded face is 0.00816 Wb, and the total flux through the six faces is 0.04896 Wb.

How to calculate magnetic flux?

The magnetic flux can be calculated through the shaded face of the cube, we need to use the formula:

Φ = B ⋅ A

where Φ is the magnetic flux, B is the magnetic field vector, and A is the area vector of the shaded face.

(a) To find the magnetic flux through the shaded face:

Given:

Edge length of the cube, ℓ = 4.00 cm = 0.04 m

Magnetic field vector, B = 5.1 î + 4.0 ĵ + 3.0 k T

The shaded face is parallel to the yz-plane, so the normal vector to this face is in the positive x-direction. Therefore, the area vector of the shaded face, A, is given by A = ℓ² î.

The magnitude of the area vector is |A| = ℓ² = (0.04 m)² = 0.0016 m²

Now, we can calculate the magnetic flux through the shaded face:

Φ = B ⋅ A

  = (5.1 î + 4.0 ĵ + 3.0 k) T ⋅ (0.0016 m² î)

  = 5.1 T × 0.0016 m²

  = 0.00816 Wb

Therefore, the magnetic flux through the shaded face is 0.00816 Weber (Wb).

(b) To find the total flux through the six faces of the cube, we need to consider that each face has the same magnitude of magnetic flux as the shaded face.

Since there are six faces in total, the total flux through the six faces is:

Total flux = 6 × Flux through the shaded face

                = 6 × 0.00816 Wb

                = 0.04896 Wb

Therefore, the total flux through the six faces of the cube is 0.04896 Weber (Wb).

Learn more about magnetic flux

brainly.com/question/31501008

#SPJ11

A pilot column breakthrough test has been performed using the phenolic wastewater in Example 12.1. Pertinent design data are inside diameter = 0.095 m, length = 1.04 m, mass of carbon = 2.98 kg, liquid flowrate = 17.42 ℓ/hr, unit liquid flowrate = 0.679 ℓ/s-m2, and packed carbon density = 401 gm/ℓ. The breakthrough data are given in Table 1. Determine:a. The liquid flowrate in bed volumes per hour and the volume of liquid treated per unit mass of carbon — in other words, the ℓ/kg at an allowable breakthrough of 35 mg/ℓ toc.b. The kinetic constants k1 in ℓ/s-kg and q0 in kg/kg.

Answers

a. The liquid flow rate in bed volumes per hour is 183.3 BV/hr, and the volume of liquid treated per unit mass of carbon (ℓ/kg) at an allowable breakthrough of 35 mg/ℓ toc is 11.1 ℓ/kg.

b. The kinetic constant k1 is 0.047 ℓ/s-kg, and the constant q0 is 0.093 kg/kg.

a. The liquid flow rate in bed volumes per hour can be calculated by dividing the liquid flow rate (17.42 ℓ/hr) by the bed volume (1.04 m × π × (0.095/2)²). This gives a flow rate of 183.3 BV/hr. The volume of liquid treated per unit mass of carbon can be calculated by dividing the liquid flow rate by the mass of carbon (2.98 kg), resulting in 11.1 ℓ/kg.

b. The kinetic constant k1 can be determined using the equation k1 = q0/C₀, where q0 is the breakthrough concentration (35 mg/ℓ toc) and C₀ is the initial concentration (0.679 ℓ/s-m² × 2.98 kg = 2.023 ℓ/kg). Thus, k1 = 0.047 ℓ/s-kg. The constant q0 can be calculated using the equation q0 = C₀ × k1, which yields 0.093 kg/kg.

These calculations provide important parameters for the pilot column breakthrough test, including the liquid flow rate, the volume of liquid treated per unit mass of carbon, the kinetic constant, and the breakthrough constant.

Learn more about carbon here:

https://brainly.com/question/13046593

#SPJ11

Other Questions
(iii) what is the maximum size of the square hole whose nominal size is 0.25? What is the final temperature when a 5.0 g sample of brass initially at 25C absorbs 75 J of heat? The specific heat of brass is 0.38 J.g^-1.C^-1 q = MCATA) -14 C B) 31 C C) 39 C D) 64C What is the main conflict in the talented Mr ripley? (book)what symbol (object, etc) could represent the title? What is the protagonist's(tom) emotional high point? (climax) Which conclusion about Columbia is best supported by the information in American as a Woman A commuter backs her car out of her garage starting from rest with an acceleration of 1. 40m/s2. How long does it take her to reach a speed of 2. 00 m/s? Which of these ideas did you include in youranswer? Check all that apply.Higher activation energies generally lead tolower reaction rates.Reaction 2 has a lower reaction rate thanReaction 1.The activation energy for Reaction 2 isprobably higher than that for Reaction 1.DONE Which equation is represented by the graph below?16&T&4Oy=e*+5Oy=e* +4Oy=Inx+421-2 -17 ?TY123 4 which species has the strongest carbon - carbon bond, c2hcl , c2h6 , or c2cl4 ? If A Population Grows 10 % Each Year, What Is The Annual Continuous (Relative) Growth Rate? A) 3.00 % B) 10.52% C) 10.00% D) 9.53% E) 7.42+% if you had each patients fasting blood sugar value and age, what procedure will you use to make comparisons among unlike data? a clamp circumcision is performed without dorsal block on a newborn. what cpt code is reported for this service? determine the steady-state growth rate in a cfstr activated sludge process as a function of sludge age. Identify an internal control procedure that would reduce the following risks in a manual system:a. The purchasing department may not be notified when goods need to be purchased. Require that an inventory control department monitor inventory records and request purchases (purchase requisition) when goods need to be reordered.b. Accounts payable may not be updated for items received. Require that the receiving department complete a receiving report for all goods received, and that a copy of the report is forwarded to accounts payable.c. Purchase orders may be prepared based on unauthorized requisitions. Require that the appropriate manager approve each purchase requisition by signing the requisition form.d. Receiving clerks may steal purchased goods. Require good physical security such as security cameras and good supervision of receiving employees. Using a "blind" PO at receiving may also help since constant shortages when goods are stolen is more likely to be noticed.e. Payments may be made for items not received. Require a three-way match of the purchase order, receiving report, and invoice before a payment can be approved.f. Amounts paid may be applied to the wrong vendor account. Assuming that the payment was to the correct vendor, but posted to the wrong account, it is very difficult to uncover this error. A reconciliation of subsidiary ledge to the accounts payable account may not uncover this because the total balance would be the same. It may be uncovered if someone notices that the records show payments to a vendor are in excess of that owed. There is no method to completely eliminate errors in posting.g. Payments may be made for items previously returned. Require a debit memorandum be completed for any goods returned, and that a copy of this be forwarded to accounts payable so that the balance owed can be changed.h. Receiving clerks may accept delivery of goods in excess of quantities ordered. First, there must be a clear policy on overshipments that receiving personnel can apply. For example, a policy may be written that overshipments under 5% can be accepted, but all others should be rejected and returned. Second, there must be a policy that all received goods are compared against a purchase order. Also, the use a "blind" PO to force receiving personnel to count goods and they might therefore more easily detect overshipments.i. Duplicate payments may be issued for a single purchase transaction. Require that payment documentation be "cancelled' when payment is made. This stamp on the documents should help prevent duplicate payments. In Microsoft Access, what do you need to decrypt an encrypted database? a. 128-bit decryption software b. an administrator account c. a password d. backup software identify how you would make hexylamine from 1-cyanopentane: let g be a group with the property that for any x, y, z in the group, xy 5 zx implies y 5 z. prove that g is abelian. ("left-right cancellation" implies commutativity.) Balance the reduction half-reaction below in acid solution. How many electrons are in the balanced half-reaction?Cr2O7 2-(aq) Cr3+(aq) F-statistics computed using maximum likelihood estimatorsA) cannot be used to test joint hypothesisB) are not meaningful since the entire regression R2 concept is hard to apply in this situationC) do not follow the standard F distributionD) can be used to test joint hypothesis A DC voltage source is connected to a resistor of resistance R and an inductor with inductance L, forming the circuit shown in the figure. For a long time before t=0, the switch has been in the position shown, so that a current I0 has been built up in the circuit by the voltage source. At t=0 the switch is thrown to remove the voltage source from the circuit. This problem concerns the behavior of the current I(t) through the inductor and the voltage V(t) across the inductor at time t after t=0.A) From t=0 onwards, what happens to the voltage V(t) across the inductor and the current I(t) through the inductor relative to their values prior to t=0?B) What is the differential equation satisfied by the current I(t) after time t=0?Express dI(t)dtin terms of I(t), R, and L.C) What is the expression for I(t) obtained by solving the differential equation that I(t) satisfies after t=0?Express your answer in terms of the initial current I0, as well as L, R, and t.D) What is the time constant of this circuit?Express your answer in terms of L and R? the portion of the obligation that plan participants are entitled to receive