Annual inspections and planned maintenance for automotive lifts have been required in american national safety standards since 1994.

To configure inter-VLAN routing on a new Layer 3 switch connected to a router, here are three steps you need to follow:

Enable IP routing: By default, Layer 3 switches operate in Layer 2 mode and do not perform routing functions. To enable inter-VLAN routing, you need to enable IP routing on the Layer 3 switch. This can usually be done using the command ip routing or ip routing enabled in the switch's configuration mode.

Create VLANs: VLANs (Virtual Local Area Networks) divide a network into logical segments, and inter-VLAN routing allows communication between these VLANs. You need to create VLANs on the Layer 3 switch to separate the different segments. Use the command vlan <vlan_id> to create each VLAN, where <vlan_id> is the identifier for each VLAN.

Configure VLAN interfaces: Each VLAN requires an interface on the Layer 3 switch to facilitate routing between VLANs. These interfaces are known as SVIs (Switched Virtual Interfaces). You need to configure an SVI for each VLAN and assign an IP address to each interface. This can be done using the command interface vlan <vlan_id> followed by the IP address assignment with the ip address <ip_address> <subnet_mask> command.

Remember that these steps assume you have already connected the Layer 3 switch to the router and have the necessary physical connections established. Additionally, there may be additional steps required depending on the specific switch model and configuration requirements.

Learn more about IP address on:

https://brainly.com/question/31171474

#SPJ1

204810 in Binary: 1100100100010102; 204810 in Hexadecimal: 4C2E16; 204810 in Octal: 624528

To convert a decimal number to binary, hexa, or octa using the division remainder method, we divide the decimal number by 2, 16, or 8, respectively. We keep dividing until the quotient is 0. The remainders at each step give us the binary, hexa, or octa digits from right to left.
For 204810, we can use the following steps:
Binary:
2048/2 = 1024 with a remainder of 0
1024/2 = 512 with a remainder of 0
512/2 = 256 with a remainder of 0
256/2 = 128 with a remainder of 0
128/2 = 64 with a remainder of 0
64/2 = 32 with a remainder of 0
32/2 = 16 with a remainder of 0
16/2 = 8 with a remainder of 0
8/2 = 4 with a remainder of 0
4/2 = 2 with a remainder of 0
2/2 = 1 with a remainder of 0
1/2 = 0 with a remainder of 1
Therefore, 204810 in binary is 1100100100010102.

Hexadecimal:
2048/16 = 128 with a remainder of 0
128/16 = 8 with a remainder of 0
8/16 = 0 with a remainder of 8
204810 in hexadecimal is 4C2E16.

Octal:
2048/8 = 256 with a remainder of 0
256/8 = 32 with a remainder of 0
32/8 = 4 with a remainder of 0
4/8 = 0 with a remainder of 4
204810 in octal is 624528.

Learn more about division remainder method here:

https://brainly.com/question/22408054

#SPJ11

The boundary that must be defined is the distance between the character and the opponent at which the character will disappear.

In order for the program to work, Asher needs to define a specific boundary distance at which the character will disappear when the opponent gets too close. This boundary distance will serve as a condition for triggering the character's disappearance. Asher can determine this boundary based on the desired gameplay mechanics and user experience. For example, the boundary could be set at a certain pixel distance between the character and the opponent, or it could be based on a predefined radius around the character. By setting this boundary, Asher ensures that the program can accurately detect when the opponent is within the defined range and initiate the character's disappearance accordingly.

Learn more about program here:

https://brainly.com/question/30613605

#SPJ11

When a cell in a table spans multiple columns, it can cause misalignment in the columns. To ensure that the columns remain aligned, you will need to adjust the width of the columns that the cell spans.

This can be done by increasing or decreasing the width of the adjacent columns so that they match the width of the combined cell. You may also need to adjust the alignment of the text in the cell to prevent it from overlapping into the adjacent columns. It is important to maintain consistency in the width and alignment of the columns throughout the table to ensure that it is easy to read and understand. Overall, making these adjustments will help to maintain the overall structure and organization of the table.

learn more about cell spans. here:

https://brainly.com/question/31756990

#SPJ11

By default, Visual Studio Code (VS Code) wraps lines of code to the next line when the screen width is insufficient to display the entire line. This behavior is controlled by the "editor.wordWrap" setting.

To automatically wrap lines in VS Code when the screen is too narrow, you can do the following:

1. Open VS Code and go to File -> Preferences -> Settings.

2. In the settings, search for "editor.wordWrap" and set it to "on" or "bounded" to enable line wrapping.

3. Additionally, you can set "editor.wordWrapColumn" to a specific value to define the column where wrapping occurs.

4. To make lines soft-wrap visually by inserting a line break without changing the actual content, enable "editor.wrappingIndent" to maintain the indentation of wrapped lines.

Furthermore, there are extensions available in the VS Code Marketplace that provide additional line-wrapping features and customization options. For example, the "Wrap Guide" extension adds visual indicators for line wrapping, and the "Prettier" extension can format code and enforce line wrapping based on configurable rules.

By adjusting the appropriate settings and utilizing extensions, you can tailor the line wrapping behavior in VS Code to suit your preferences and ensure code readability on narrower screens.

learn more about visual studio code here; brainly.com/question/31040033

#SPJ11

A compound spur gear train with a -250:1 ratio and 9 diametral pitch requires pitch diameters of 1.800" and 0.0072", with tooth numbers of 90 and 36, respectively.

A compound spur gear train is designed to achieve a -250:1 ratio and a diametral pitch of 9. The pitch diameters can be calculated using the formula Pa = N/d, where Pa is the pitch diameter, N is the number of teeth, and d is the diametral pitch.

For the desired ratio, two gears are required: one with 90 teeth and a pitch diameter of 1.800", and the other with 36 teeth and a pitch diameter of 0.0072". The larger gear will transmit power from the input to the intermediate gear, and the smaller gear will drive the output.

By combining these gears in a compound arrangement, the desired gear ratio is achieved.To understand the design of a compound spur gear train in detail, it is essential to study the principles of gear systems, gear ratios, and how pitch diameters and tooth numbers are calculated.

This will provide a comprehensive understanding of gear train design and enable further exploration into more complex gear systems.

Learn more about spur gear

brainly.com/question/13087932

#SPJ11

Remote Desktop is a remote access mechanism on Windows systems that enables monitoring and control of a user's desktop.

It allows administrators or authorized individuals to observe the user's actions in real-time and perform necessary configuration tasks. By establishing a remote connection, Remote Desktop grants the ability to view the user's screen, access files and applications, and interact with the desktop as if physically present. This capability proves valuable for troubleshooting, providing support, or managing remote systems efficiently. It enhances collaboration and facilitates efficient remote administration, allowing users to address issues, configure settings, and ensure seamless operation without requiring physical proximity to the target machine.

Learn more about Windows systems here;

https://brainly.com/question/11496677

#SPJ11

The program would print "5 10" as the modified price is 5 and the original price remains unchanged at 10.

The program will print the modified price of the item followed by the original price of the item, separated by a space.

In the provided code snippet, the `discount` function takes a pointer to an `item` structure and an integer `price` as parameters. It reduces the `price` by 5 and updates the `price` attribute of the `item` structure accordingly. Then, it assigns the null value to the `item` pointer, which has no effect outside the function due to the call-by-reference nature of C.

Assuming the function is called with an `item` structure containing an original price value of 10, the program would print "5 10" as the modified price is 5 and the original price is still 10.

Learn more about program

brainly.com/question/30613605

#SPJ11

Recursion programming is a technique used in computer programming where a function calls itself in order to solve a problem. In the case of the sumtok function, we want to find the sum of the values from 1 to k using recursion.

To solve this problem recursively, we need to break it down into smaller subproblems. In this case, we can start by finding the sum of the values from 1 to k-1, and then add k to this sum.

Therefore, the missing recursive call in the sumtok function should be:

return k + sumtok(k-1);

This will keep calling the sumtok function recursively until the base case is reached (when k is less than or equal to 0). Once the base case is reached, the function will start returning the values to the previous recursive call until the final sum is obtained.

In summary, the sumtok function uses recursion programming to find the sum of values from 1 to k. It breaks the problem down into smaller subproblems by calling itself recursively and returns the final sum once the base case is reached.

For more information on Recursion programming visit:

brainly.com/question/29557618

#SPJ11

The `fun` function takes a premise and a list, and returns a new list containing elements of the input list that satisfy the given premise.

Here is a scheme function that takes a premise and a list, and returns a new list containing all elements of the input list that satisfy the given premise:
```
(define (fun premise lst)
 (cond ((null? lst) '())         ; base case: empty list
       ((premise (car lst))     ; if premise is true for first element
        (cons (car lst)         ; include it in the result
              (fun premise (cdr lst))))
                               ; recur on the rest of the list
       (else (fun premise (cdr lst))))) ; premise is false, recur on rest of list
```
Here's how to use the function:
```
> (fun (lambda (a) (< a 10)) '(1 2 12 14 15))
(1 2)
```
In this example, the premise is `(lambda (a) (< a 10))`, which tests whether a given element is less than 10. The input list is `(1 2 12 14 15)`, and the expected output is `(1 2)`. The `fun` function filters out all elements of the input list that are not less than 10, and returns the result list.

Learn more about input list here;

https://brainly.com/question/30025939

#SPJ11

Among the given cell types, macrophages are not derived from lymphoid progenitors.

So, the correct answer is A

B cells, helper T cells, and cytotoxic T cells are all part of the lymphoid lineage and are involved in adaptive immunity. Macrophages, on the other hand, are part of the myeloid lineage and play a key role in innate immunity.

They are derived from monocytes and are responsible for phagocytosis, which is the process of engulfing and destroying pathogens, as well as stimulating other immune cells by presenting antigens. In summary, macrophages are the cell type not derived from lymphoid progenitors.

Hence ,the answer of the question is A.

Learn more about macrophage at https://brainly.com/question/32203404

#SPJ11

TRUE. An identifier is a candidate key that has been selected as the unique, identifying characteristic for an entity type. In database design, an entity type represents a type of object or concept that has a set of attributes or properties. For example, an entity type could be "customer" or "product" in an e-commerce system.

Each instance or occurrence of the entity type is uniquely identified by an identifier, which is a set of one or more attributes that together uniquely identify the instance. A candidate key is a set of one or more attributes that could potentially serve as an identifier for an entity type. However, not all candidate keys are suitable as identifiers, as they may not be unique or stable enough to reliably identify the instances of the entity type.

Therefore, a single candidate key is selected as the identifier for the entity type, and this key is used as a reference or foreign key in other tables that have a relationship with the entity type. In summary, an identifier is a specific candidate key that has been chosen as the unique, identifying characteristic for an entity type. It is an essential element of database design that enables data to be organized and accessed efficiently.

Learn more about e-commerce here-

https://brainly.com/question/31073911

#SPJ11

When calling functions, it is important to push and pop register values for several reasons. First, pushing register values can help prioritize processes and ensure that the function being called receives the necessary resources to execute properly. Second, pushing and popping register values can help ensure that parameters passed to called functions are properly registered and can be accessed by the function. This is critical for functions that rely on input parameters to perform calculations or execute specific tasks.

Another important reason for pushing and popping register values is to ensure that necessary values in call-used registers are not overwritten or clobbered by called functions. Call-used registers are registers that are typically used to store intermediate results or temporary values during function execution. If these registers are clobbered by a called function, it can cause unexpected results and even system crashes.

Finally, it is important to note that pushing error codes so that they are ignored is not a valid reason for pushing and popping register values. Error codes should never be ignored, as they can indicate serious issues that need to be addressed and resolved.

In summary, pushing and popping register values when calling functions is essential for ensuring that the function being called receives the necessary resources, parameters are properly registered, and call-used registers are not overwritten. It is important to follow proper programming practices and avoid ignoring error codes, as they can indicate serious issues that need to be addressed.

More question related to pushing & popping : https://brainly.com/question/17177482

#SPJ11

A program is a set of instructions written in a computer language that tells a computer what to do. Programs are created by software developers to perform specific tasks or solve specific problems.

The program seems to be a file processing tool that allows users to choose a file for processing. When the program starts, the user is presented with two options - to select a file to process or to exit the program. If the user chooses to select a file, they are then presented with three further choices about which file to process. The details of these three choices are not provided in the question, but it is assumed that they are related to the type or location of the file.

On the other hand, if the user chooses to exit the program, the program should terminate. It is important to note that proper error handling should be implemented to ensure that the program exits gracefully. This can include closing any open files, freeing up memory, and terminating any running processes.

Overall, the program seems to be a simple tool for file processing that provides users with a limited set of options. However, it is important to ensure that the program is user-friendly, easy to navigate, and robust enough to handle any errors or unexpected inputs. By doing so, the program can provide a useful and efficient tool for processing files.

To know more about program visit:

https://brainly.com/question/3224396

#SPJ11

False. Zero compression is used to reduce the size of the IPv6 address by replacing consecutive blocks of zeros with a double colon (::), not two colons.

This compression technique is applied to condense long sequences of zeros within an IPv6 address to make it more concise. By using zero compression, an IPv6 address can be represented in a shorter format, eliminating the need to write consecutive blocks of zeros. This helps in reducing the length and improving the readability of the address. However, it's important to note that zero compression can only be applied once within an IPv6 address to avoid ambiguity.

Learn more about zero compression here:

https://brainly.com/question/20563673

#SPJ11

The other two code segments are also attempting to count the number of negative values in nums, but they have errors. Code segment 1 uses a while loop that starts at -1 and increments i until it reaches the second to last index of nums.

The code segment that counts the number of negative values found in nums and stores the count in counter is code segment number 2:

int counter = 0;
for (int i = 1; i < nums.length; i++){
   if (nums[i] < 0){
       counter++;
   }
}

This code initializes a counter variable to 0 and then loops through the array nums using a for loop. Inside the loop, it checks if the current element is negative (less than 0) and if it is, it increments the counter variable. Once the loop has finished iterating through all the elements in nums, the final count of negative values will be stored in the counter variable.

To know more about code segments visit:-

https://brainly.com/question/30353056

#SPJ11

The correct syntax for importing modules from the script readFile.py is:  `import readFile`

In Python, modules are files containing Python definitions and statements, which can be used in other Python scripts. To use functions or variables defined in a module, we need to import it into the script where we want to use it. The syntax for importing a module is `import module_name`. In this case, the module is `readFile.py`, so the correct syntax for importing it is `import readFile`. This statement allows us to access functions and variables defined in the `readFile.py` module using the `readFile.function_name` or `readFile.variable_name` syntax in the importing script. Once imported, we can use the functions and variables of the module as needed in our code.

Learn more about syntax here;

https://brainly.com/question/31605310

#SPJ11

If the cordless phones are causing interference with the wireless network transmissions in the small office, the network could be using the 802.11b and Bluetooth wireless standards.

The 802.11b wireless standard operates in the 2.4GHz frequency range, which is the same frequency range used by many cordless phones. This overlap can lead to interference between the cordless phones and the wireless network transmissions. Therefore, if the network in the small office is using the 802.11b standard, it is susceptible to interference from the cordless phones. Bluetooth is another wireless standard that operates in the 2.4GHz frequency range. It uses frequency-hopping spread spectrum technology to mitigate interference. However, if the cordless phones in the office are also operating in the 2.4GHz frequency range, they can still cause interference with the Bluetooth devices and the wireless network.

Infrared, 802.11a, and 802.3a are not likely to be affected by cordless phones as they operate in different frequency ranges. Infrared is a short-range wireless communication technology that uses light waves, while 802.11a operates in the 5GHz frequency range, and 802.3a is a wired Ethernet standard. Therefore, the wireless standards that could be affected by cordless phone interference in the small office are 802.11b and Bluetooth.

Learn more about network here: https://brainly.com/question/30456221

#SPJ11

The author has not provided their opinion on the best feature selection algorithm to use in the given scenario, but has asked the reader to make their own judgement based on their knowledge of these algorithms and to explain their reasoning.

The choice of algorithm depends on the nature of the data, the size of the feature space, the type of learning algorithm being used, and the goals of the analysis.

Some commonly used feature selection algorithms include filter methods such as correlation-based feature selection and mutual information, wrapper methods such as recursive feature elimination and genetic algorithms, and embedded methods such as LASSO and Ridge regression.

Each algorithm has its strengths and weaknesses, and the best choice will depend on the specific characteristics of the data and analysis.

Learn more about algorithm

brainly.com/question/31936515

#SPJ11

The program fills a list box with film genres and displays Oscar-winning films when a genre is clicked.

The program is designed to create a user interface that includes a list box populated with various film genres. When the user clicks on a specific genre, the program retrieves and displays a list of Oscar-winning films belonging to that genre.

To accomplish this, the program utilizes event handling to capture the user's selection from the list box. Once a genre is selected, the program accesses a database or a predefined list of Oscar-winning films to retrieve the relevant films corresponding to the chosen genre.

The retrieved films are then presented to the user in a visually appealing and easily readable format, such as a separate list or a dialog box.

Learn more about program

brainly.com/question/30613605

#SPJ11

For both Firefox and Internet Explorer, the menu bar is hidden until you press the "Alt" key.

In web browsers like Firefox and Internet Explorer, the menu bar contains various options and settings that allow users to navigate through different menus and access browser features. By default, the menu bar is often hidden to provide a cleaner and more streamlined browsing experience. However, users can reveal the menu bar whenever needed by pressing the "Alt" key on their keyboard. Pressing the "Alt" key triggers a temporary display of the menu bar, allowing users to access the different menus such as File, Edit, View, Tools, and Help. Once a menu option is selected or if the user clicks outside the menu area, the menu bar automatically hides again to maximize the available screen space for web content.

This keyboard shortcut provides a convenient way for users to access the menu bar on-demand, without it permanently occupying space on the browser interface when not in use.

Learn more about Internet here: https://brainly.com/question/28347559

#SPJ11

The routing prefix in IPv6 is like the "network" part in an IPv4 address.

In both IPv4 and IPv6 addressing schemes, the address is divided into two main parts: the network portion and the host portion. The network portion identifies the network to which the device belongs, while the host portion identifies the specific device within that network. In IPv4, the network portion is determined by the subnet mask, which specifies the number of network bits. The remaining bits represent the host portion. Similarly, in IPv6, the routing prefix specifies the network portion, while the remaining bits are used for the host portion.

Learn more about IPv6 addressing and routing here:

https://brainly.com/question/4594442

#SPJ11

The process responsible for managing most of the operations on an ESXi host is the vmkernel.

The vmkernel is the core component of the ESXi hypervisor that handles various operations and manages resources on an ESXi host. It is responsible for managing most of the key functions and services that enable virtualization. The vmkernel operates as the liaison between the virtual machines (VMs) and the underlying hardware. It handles tasks such as CPU scheduling, memory management, I/O operations, and network stack. It ensures efficient allocation and utilization of hardware resources among VMs, providing isolation and performance guarantees.

Additionally, the vmkernel is responsible for managing and executing VMkernel modules, including drivers and other system services. These modules handle device and storage drivers, network protocols, file systems, and other essential components for the proper functioning of the ESXi host. Overall, the vmkernel plays a critical role in the operation of an ESXi host, managing most of the core functions and facilitating the virtualization capabilities of the host.

Learn more about network here: https://brainly.com/question/30456221

#SPJ11

To connect a wireless router to a laptop in Cisco Packet Tracer, follow these steps:

1. Open Cisco Packet Tracer.
2. Select the "End Devices" category on the bottom-left side of the screen.
3. Drag and drop the "Laptop" icon onto the workspace.
4. Select the "Network Devices" category and then the "Wireless Devices" subcategory.
5. Drag and drop the "Wireless Router" icon onto the workspace.
6. Select the "Connections" category (represented by a lightning bolt icon).
7. Choose the "Wireless" connection type (represented by a jagged line).
8. Click on the Wireless Router, then click on the Laptop to establish a wireless connection between the devices.

Cisco Packet Tracer is a network simulation tool that allows users to create virtual networks and test their configurations. In this case, we are connecting a wireless router to a laptop using the wireless connection type, which simulates a Wi-Fi connection between the devices.

To know more about router, visit;

https://brainly.com/question/24812743

#SPJ11

The configuration file that should hold the configuration information for the file systems to be mounted each time the system is brought up is the /etc/fstab file. This file contains information about the file systems that are automatically mounted during system startup, including their device names, mount points, file system types, and mount options.

In communications or computer systems, a configuration of a system refers to the arrangement of each of its functional units, according to their nature, number and chief characteristics. Often, configuration pertains to the choice of hardware, software, firmware, and documentation. Along with its architecture, the configuration of a computer system affects both its function and performance.

To learn more about "Configuration" visit: https://brainly.com/question/14114305

#SPJ11

False. When a user interacts with a computer, they typically interact with the user interface provided by the operating system, such as graphical user interfaces (GUI) or command-line interfaces (CLI).

The kernel is the core component of an operating system that manages system resources, controls hardware devices, and provides essential services. It operates at a lower level than the user interface and handles tasks related to process management, memory management, device drivers, and other system-level operations. In summary, the user interacts with the user interface provided by the operating system, and the user interface interacts with the kernel to perform the necessary operations on behalf of the user.

Learn more about the operating system here:

https://brainly.com/question/6689423

#SPJ11

The correct SQL statement to assign the DBA role as the default role for user RTHOMAS is option c: ALTER USER rthomas SET DEFAULT TO DBA.

Explanation:

Among the provided options, option c: ALTER USER rthomas SET DEFAULT TO DBA is the correct SQL statement to assign the DBA role as the default role for user RTHOMAS.

In SQL, the ALTER USER statement is used to modify user properties, including their default role. By specifying the SET DEFAULT TO clause followed by the desired role (in this case, DBA), the statement sets the specified role as the default role for the user.

Option a: ALTER USER rthomas DEFAULT ROLE dba is not a valid SQL syntax for assigning the default role.

Option b: SET ROLE DBA is used to explicitly switch the current session's role to DBA, but it does not set the DBA role as the default role for the user.

Therefore, the correct option for assigning the DBA role as the default role for user RTHOMAS is option c: ALTER USER rthomas SET DEFAULT TO DBA.

Learn more about SQL statement here:

https://brainly.com/question/32322885

#SPJ11

The recursive definition for bCount can be defined as follows:
Base case:
- If x is an empty string, bCount(x) = 0.

Recursive case:
- If the last character of x is b, bCount(x) = bCount(y) + 1, where y is the string obtained by removing the last character from x.
- If the last character of x is a, bCount(x) = bCount(y), where y is the string obtained by removing the last character from x. This definition essentially breaks down the problem into smaller sub-problems, where the bCount of a string is dependent on the bCount of a smaller sub-string. By reducing the size of the string in each recursive call, we eventually arrive at the base case where the string is empty and the bCount is 0. For example:
- bCount("abb") = bCount("ab") + 1 = bCount("a") + 1 = 0 + 1 = 1
- bCount("ababab") = bCount("ababa") + 1 = bCount("abab") + 1 = bCount("aba") + 1 = bCount("ab") + 1 = bCount("a") + 1 = 0 + 1 = 1

Learn more about recursive call here:

https://brainly.com/question/29238776

#SPJ11

Answer:

To count the number of words in a string `text`, you can follow these steps:

1. Split the string into a list of words using a whitespace as the delimiter.

2. Count the number of elements in the resulting list.

Here's an example implementation in Python:

```python

def count_words(text):

   words = text.split()  # Split the string into words

   return len(words)  # Count the number of words

# Example usage:

text = "Hello, how are you today?"

word_count = count_words(text)

print("Number of words:", word_count)

```

In this example, the `count_words` function takes a string `text` as input. It uses the `split` method to split the string into words and stores them in a list called `words`. Finally, it returns the length of the `words` list, which represents the number of words in the string.

Note that this implementation assumes that words are separated by whitespace characters. If your definition of a word differs, you may need to adjust the splitting logic accordingly.

Learn more about **string manipulation in Python** here:

https://brainly.com/question/30401673?referrer=searchResults

#SPJ11

To solve this problem, we can first find the total number of possible strings of 3 lowercase English alphabets, which is 26^3 = 17576.

Next, we need to find the number of strings that do not contain the letter ‘c’. This can be calculated by considering that there are 25 options for the first letter (all letters except ‘c’), 25 options for the second letter (as the first letter can be any letter except ‘c’, and so on for the third letter. Therefore, the number of strings without the letter ‘c’ is 25^3 = 15625.

Finally, to find the number of strings that have at least one ‘c’ in it, we can subtract the number of strings without ‘c’ from the total number of possible strings, giving us 17576 - 15625 = 1951.

Therefore, there are 1951 strings of 3 lowercase English alphabets that will have at least one ‘c’ in it, if letters can be repeated.

For such more question on alphabets

https://brainly.com/question/29103592

#SPJ11

There are 1951 strings of 3 lowercase English alphabets that will have at least one 'c' in it.

To find the number of strings of 3 lowercase English alphabets that will have at least one 'c' in it, we can use the concept of complementary counting. We can first find the total number of strings of 3 lowercase English alphabets without any restrictions on the letters, and then subtract the number of strings that do not contain any 'c's. The result will give us the number of strings with at least one 'c' in it.

The total number of strings of 3 lowercase English alphabets without any restrictions on the letters is given by 26^3, since there are 26 choices for each of the three positions.

The number of strings that do not contain any 'c's is given by 25^3, since there are 25 choices for each of the three positions when 'c' is excluded.

Therefore, the number of strings of 3 lowercase English alphabets with at least one 'c' in it is:

26^3 - 25^3 = 17576 - 15625 = 1951

So there are 1951 strings of 3 lowercase English alphabets that will have at least one 'c' in it.

Learn more about strings here:

https://brainly.com/question/30099412

#SPJ11