It is possible to design a reactor where the scy conductor and the nitrogen/ammonia electrode operate at different temperatures. Which combination of temperatures is expected to give the best results?.

Answers

Answer 1

The combination of temperatures that is expected to give the best result is option A: SCY temperature higher than electrode temp.

Why the case above?

The answer is option A because the proton conductivity of SCY is known to be one that often goes up along with increasing temperature, and the favorability of reaction goes down or reduces with total temperature.

Hence, It is said to be good for one to to keep the SCY conductor at a higher temperature and as such, The combination of temperatures that is expected to give the best result is option A: SCY temperature higher than electrode temp.

See options below

. Which combination of temperatures is expected to give the best results?

A.

SCY temperature higher than electrode temperature

B.

SCY temperature lower than electrode temperature

C.

SCY temperature the same as electrode temperature

D.

The temperature of the components does not make a difference.

Learn more about reactor from

https://brainly.com/question/15051406

#SPJ1


Related Questions

Which section(s) of the Code emphasize the fact that all circuiting must be done so as to avoid the damaging effects of induction heating

Answers

The section(s) of the Code emphasize that all circuiting must be done so as to avoid the damaging effects of induction heating is 300.35, 300.3(B), and 300.20(A).

What is induction heating?

The term induction heating is known to be a form of heating of material that occurs via an electric current that makes a flow via the material or its container through the means of electromagnetic induction.

Hence, The section(s) of the Code emphasize that all circuiting must be done so as to avoid the damaging effects of induction heating is 300.35, 300.3(B), and 300.20(A).

Learn more about heating from

https://brainly.com/question/13982702

#SPJ1

6.
Describe the procedure for ensuring that all documentation relating to the work being carried out is
available, prior to starting the activity

Answers

Workplace documentation includes all the paperwork HR must gather from each employee.

What is a documentation at work?

Any communicable material used to describe, clarify, or provide instructions for certain characteristics of a thing, a system, or a procedure, such as its components, assembly, installation, maintenance, and use, is considered documentation.

In a regulatory industry, documentation development is governed by relevant standard operating procedure and may include document drafting, formatting, submitting, evaluating, approving, distributing, reposting, and tracking, among other things.

It might also entail writing original content. Documentation must to be simple to read and comprehend. It could be misread or ignored if it is very wordy and lengthy. Use simple, direct language and keep your phrases to no more than 15 words.

Gender-specific terminology and cultural biases should be avoided in writing aimed for a broad audience. Steps in a process chain should be distinct from one another.

To learn more about documentation refer to:

https://brainly.com/question/28170598

#SPJ1

Determine the rectangular and polar radii of gyration of the shaded area about the axes shown. Show steps please.

Answers

The polar radius of gyration can then be computed by dividing the moment of inertia by the area, A, of the shaded area: Rp = √(Ip/A).

What is polar radius?

Polar radius is a measure of the distance from the center of a planet or other celestial body to its pole. It is measured in kilometers and is usually slightly smaller than the equatorial radius. Polar radius is important in determining the shape of a planet or other celestial body, as the ratio of the polar radius to the equatorial radius is known as the flattening.

The rectangular radii of gyration (Rx, Ry) of the shaded area are calculated by taking the moments of inertia of the area with respect to the two axes and dividing them by the area. The moments of inertia in the x and y directions are defined as:
Ix = ∫ y2 dA
Iy = ∫ x2 dA
The rectangular radii of gyration can then be computed by dividing each of the moments of inertia by the area, A, of the shaded area:
Rx = √(Ix/A)
Ry = √(Iy/A)
The polar radii of gyration (Rp) of the shaded area is calculated by taking the polar moment of inertia of the area and dividing it by the area. The polar moment of inertia is defined as:
Ip = ∫ r2 dA
The polar radius of gyration can then be computed by dividing the moment of inertia by the area, A, of the shaded area:
Rp = √(Ip/A)

To learn more about gyration
https://brainly.com/question/15127397
#SPJ4

In high-wind installations, if an old composition asphalt shingle roof is going to be replaced, the roofing contractor should ___________ the existing shingles and underlayment.

Answers

In regards to high-wind installations, if an old composition asphalt shingle roof is going to be replaced, the roofing contractor should remove the existing shingles and underlayment.

What are High Wind installations?

High Wind is known to be a newly created installation techniques that is often used in the installation of offshore wind turbines and this is often done at  higher wind speeds.

Note that, In regards to high-wind installations, if an old composition asphalt shingle roof is going to be replaced, the roofing contractor should remove the existing shingles and underlayment.

Learn more about installations from

https://brainly.com/question/13093522

#SPJ1

What protection must be provided when installing a cable in a notched stud or joist, or when a cable is run through bored holes in a stud or joist where the distance is less than NEC guidelines from the edge of the framing member to the cable

Answers

The protection that  must be provided when installing a cable in a notched stud or joist are:

A steel "kick" platebushings or grommets

What protection must be provided when installing a cable in a notched stud or joist?

If a nonmetallic cables is said to pass through holes or slots in metal framing members, the cable that need to ]be protected is through bushings or grommets and it is used to cover all metal edges and rightly fastened in the opening before one can install the cable.

Hence, The protection that  must be provided when installing a cable in a notched stud or joist are:

A steel "kick" platebushings or grommets

Learn more about cable installation from

https://brainly.com/question/14721758

#SPJ1

Backing strips that are to be removed after welding are normally ?
A. of the same material as the base metal
B. are made of a different material than the base metal
C. are rarely made of copper
D. ground off after welding

Answers

Typically, backing strips that will be removed after welding are constructed of a substance other than the base metal.

Do support bars need to be taken off?

These backer bars cannot be removed, thus they must be left in place. For structures that are statically loaded, this is usually fine. In most cases, backing must be continuous.

What are the purposes of backing bars?

At the base of a welded junction, a weld backer bar is used to support the molten weld metal, making it easier to obtain a fully penetrated joint. Before the groove weld is finished, a steel backing bar may be placed using a discontinuous/continuous fillet or tack weld.

To know more about welding visit:-

https://brainly.com/question/29654991

#SPJ1

The four diagonals of a cube are drawn to create 6 square pyramids with the same base and height. The volume of the cube is (b)(b)(b). The height of each pyramid is h. Therefore, the volume of one pyramid must equal one-sixth the volume of the cube, or (b)(b)(2h) or bh. (b)(b)(6h) or bh. (b)(b)(6h) or bh. (b)(b)(2h) or bh.

Answers

The volume of one pyramid must equal one-sixth the volume of the cube, or 1/6(b)(b)(2h) or 1/3Bh. Thus, the correct option is A.

What is pyramid?

A pyramid has three dimensions. A pyramid has a polygonal base and flat triangular faces that come together at a point known as the apex. By connecting the bases to the apex, a pyramid is formed.

The lateral face is formed by connecting each edge of the base to the apex. A pyramid with n sides has n+1 faces, n+1 vertices, and 2n edges.

Given that

The cube is divided into 6 same pyramids

Volume of pyramid = 1/3(S)(h)

Here,

S = B

So, Volume  = 1/3(B)(h)

Also for cube

Volume of cube = b³ = b² ×2h

Volume of pyramid = 1/6th of Volume of cube

= 1/6 × b² ×2h

Thus, the volume of one pyramid must equal one-sixth the volume of the cube, or 1/6(b)(b)(2h) or 1/3Bh.

Learn more about pyramid

https://brainly.com/question/17615619

#SPJ4

Name the design tool that can be used to establish a spatial hierarchy of the content (1)Proportion (2)Hierarchy (3)Balance (4)Grids

Answers

The design tools that can be used to establish a spatial hierarchy of the content:

1. Hierarchical proportion

2. Typography

3. Grouping and Alignment

4) Image Size

What is spatial hierarchy?

A spatial hierarchy is understood as a geographic grouping of regions where there are significant differences in the dynamics of innovation and growth between the clusters. A quick review of the literature on local innovation and growth is conducted. Following that, a database on the dynamics of regional growth and innovation in Europe is presented.

The possibility of a spatial hierarchy in Europe is investigated using spatial principal component analysis and spatial correlation analysis. The findings point to a hierarchy made up of two groups in West and North Europe, one group each in South and East Europe. A few policy conclusions are reached after discussing the growth and innovation performance in these clusters.

Learn more about spatial hierarchy

https://brainly.com/question/12076206

#SPJ4

A rapid mixer disperse chemicals in a flow of 20,000 m3/day. The detention time is 30 s, and G is 700/s. What is the power required for this mixer?

Answers

The power required for this mixer is 14700000 Watts.

How can we determine the value of power required by the mixer?

The power required for the mixer can be calculated using the following formula:

Power = (G^2 * Detention Time) / (Flow Rate * 8.34)

where G is the mixer's specific energy input in m^3/s^3, Detention Time is the time the liquid spends in the mixer in seconds, Flow Rate is the flow of the liquid through the mixer in m^3/s, and 8.34 is a constant.

Plugging in the given values:

Power = (700^2 * 30) / (20000/86400 * 8.34)

Power = (490000 * 30) / (0.002314814814814815)

Power = 14700000

So the power required for this mixer is 14700000 Watts.

Therefore, the correct answer is as given above. It can be concluded that the power required for this mixer is 14700000Watts.

learn more about Power: https://brainly.com/question/2248465

#SPJ1

(a) e = n/1-n = 0.3/1-0.3 = 0.43
Bulk density ? = Gspw(1+w)/1+e = 2.7x1000(1+0.1)/1+0.43 = 2079.0 kg/m3

(b) Saturated density psat= GsPw+epw / 1+e = 2.7x1000+0.43x1000/1+0.43 = 21

Answers

For the specified values, the saturated density is 430 Kg/m3, whereas the bulk density is 2700 Kg/m3.

Given data

Void ratio e = 0.43

Specific gravity Gs = 2.7

density of water ρw = 1000 Kg/m^3

1)Mass of soil solids = Gs ρw

= 2.7*1000

= 2700 Kg/m^3

2)Value of eρw

= 0.43*1000

=430 Kg/m^3

Soil compaction is indicated by bulk density. It is determined by dividing the dry weight of the soil by its volume.

Both the volume of soil particles and the volume of soil particle pores are included in this volume. Typically, bulk density is stated in g/cm3.

The Influence of Inherent - The density of soil mineral (sand, silt, and clay) and organic matter particles, as well as how they are packed, all affect bulk density. As a general rule, the bulk density of most rocks is 2.65 g/cm3, hence the optimal soil is one with a medium texture.

Learn more about Bulk here:

https://brainly.com/question/7139086

#SPJ4

A __________ is a single lane used by drivers to enter and exit a freeway. a) Climbing lane b) Weave lane c) Thru lane d) Offset lane

Answers

A Weave lane is a single lane used by drivers to enter and exit a freeway.

What is this lane about?

Weave lanes are known to be lanes that acts as an entrance and exits for a lot of cars in highways.

Hence, one can say that A Weave lane is a single lane used by drivers to enter and exit a freeway.

Learn more about Weave lane from

https://brainly.com/question/10828527

#SPJ1

For the frame and loading shown, determine the components of all forces acting on member ABD.

Answers

The component of forces acting on member ABD Aₓ and A[tex]_y[/tex] are 1390lb← and 740lb↑ respectively.

What is component of forces?

A component is a piece that makes up something. Similar to how parts of a force are expressed by pointing in their directions, so does a force. These are typically categorised as vertical and horizontal components.

If I push you horizontally with some force, the horizontal force component is equal to the total force, and the vertical force component is equal to zero.

The horizontal component of force is F·cos30° and the vertical component is F·cos30 if a bullet is fired at, say, a 30° angle to the horizontal, and you draw a right-angled triangle with the bullet's path as the hypotenuse (though it's parabolic for long distances).

Calculate the reaction force acting at E

Take the moments about point A

[tex]\begin{gathered}\\\sum M_A=0 \\\left(E_x\right)(12)-(430)(15)-(310)(33)=0 \\E_x=1390 lb \\A_x=1390 lb\\\\\end{gathered}[/tex]

Now,

[tex]A_y - 430 -310 = 0\\A_y = 740 \ lb[/tex]

Take the moments about point B

[tex]\Sigma M_b =0\\(D-y)(18)- 740\times 6 = 0\\D-y=246.55\lb[/tex]

Substitute 2780 lb for Dx

[tex]B_x+D_x-1390=0[/tex]

[tex]\\B_x+2780-1390=0 \\B_x=-1390\ \text{lb}[/tex]

Consider the equilibrium equation along y axis in the member ABD, Substitute 246.66 lb for Dy

[tex]\\B_y+D_y+740=0\\B_y+246.66+740=0 \\B_y=-986.66 \mathrm{lb}\end{gathered}[/tex]

Using the free body diagram of member ABD and the equilibrium equations the component forces Bx and By have been calculated. Since we got negative values for Bx and By that means the direction of forces Bx and By are opposite to the assumed direction.

Thus, The component forces Aₓ and A[tex]_y[/tex] are 1390lb← and 740lb↑ respectively.

Learn more about  component of forces

https://brainly.com/question/15443509

#SPJ4

On 2023 z with a manual transmission. When the clutch is engaged, what is the first step to shift into reverse?

Answers

The first step that is needed in order to shift the reverse would be to Push down on the shift lever.

What is meant by a manual transmission?

This is the term that is used in driving to explain the scenario that occurs due to the fact that a person has to go through a system of changing gears while they are driving. An example of how this is used is when a person says that there car has a manual transmission instead of automatic transmission.

This would mean that this person would be the one that would be changing the gears while driving on their own. To do this what would be done is to Push down on the shift lever.

Read more on driving here: https://brainly.com/question/1557131

#SPJ1

Is an element of Total Stopping Distance.
a) Braking Distance
b) Reaction Distance
c) Perception Distance
d) All of the above are correct

Answers

A: Braking Distance,  B: Reaction Distance, C: Perception Distance all are elements of Total Stopping Distance. So option D: "all of the above are correct" is the correct answer choice.

Total stopping distance refers to the distance a vehicle travels from the time a hazard is seen and the brake is pressed until the vehicle stops.  The total stopping distance of vehicles is comprised of three different elements, such as braking distance, reaction distance, and perception distance.

Perception Distance: The distance a vehicle travels while a driver is determining, predicting, and deciding to slow down for a hazard.Reaction Distance: It is the time it takes for a driver to act upon a decision once a danger is recognized. The distance a vehicle travels while the driver reacts is called a reaction distance.Braking Distance: The distance a vehicle travels from the time a driver starts pressing on the brake pedal until the time vehicle comes to a stop.

You can learn more about total stopping distance at

https://brainly.com/question/24020960

#SPJ4

determine the reactions at the supports a and b. ei is constant. neglect the effect of axial load.

Answers

The reactions at the supports a and b. ei is constant. neglect the effect of axial load will be 0 0.

What is axial load?
Axial load
, also called thrust load, is a type of force that is applied along the axis of a component or structure. It is a compressive or tensile force which acts in the direction of the axis of an object. It is usually caused by an external force, such as an applied load, or by an internal force, such as the thrust generated by a motor. Axial loads can be static, meaning that the force is constant, or dynamic, meaning that the force changes over time. Axial load can cause deformation, or bending of the component. It can also cause stress, which can lead to fatigue and failure.

At support A:

Reaction in the x-direction: ei*(0-5) = -5ei

Reaction in the y-direction: 0

At support B:

Reaction in the x-direction: ei*(15-10) = 5ei

Reaction in the y-direction: 0

To learn more about axile load
https://brainly.com/question/15713784

#SPJ4

please answer the question

Answers

The discrepancy between experimental and theoretical entropy values can be used to determine residual entropy.

What, using an example, is residual entropy? The discrepancy between experimental and theoretical entropy values can be used to determine residual entropy.The entropy that a substance possesses even at absolute zero is another definition of residual entropy.Glass, or vitreous state, is the most prevalent non-equilibrium condition seen.Carbon monoxide is yet another case in point.The dipole moment of it is small.Included in the list of examples is an amorphous solid.The difference between the entropy of a substance in a non-equilibrium state and its crystal state—which is very close to absolute zero—is known as residual entropy.In comparison to the experimental residual entropy of 3.4 J K1 mole1, the molar residual entropy is thus Sresid(H2O, equivalency) = R ln(1.5) = 3.37 J K1 mole1.

To learn more about entropy refer

https://brainly.com/question/29311952

#SPJ1

The SMART technique for problem solving
was introduced. In this approach, S stands for
specific
measurable
achievable
realistic
, M stands for
"
A stands for
"
R stands for
"
and T stands for

Answers

Note that the SMART technique for problem-solving and goal-setting was introduced. In this approach:

S stands for specificM for measurableA for achievableR for realisticand T stands for Time Bound.

What is problem-solving?

The act of describing a problem, discovering the origin of the problem, finding, prioritizing, and selecting alternatives for a solution, and executing a solution is known as problem-solving.

Employers value problem-solving abilities because they demonstrate a variety of other qualities such as logic, creativity, resilience, imagination, lateral thinking, and drive. It is a necessary ability for both your professional and personal life.

Learn more about Problem-Solving:
https://brainly.com/question/29438624
#SPJ1

A cylindrical component constructed from an S-590 alloy (Figure 8.31) has a diameter of 20.3 mm (0.7992 in.). Determine the maximum load that may be applied for it to survive 1000 h at 925�C (1700�F).

Answers

The maximum load of 13889 N is required to survive the condition. for A cylindrical component constructed from an S-590 alloy (Figure 8.31) has a diameter of 20.3 mm (0.7992 in.)

Calculate the tensile load using the stress relation.

σ = F/A

Here, A is the area of the bar and σ is the stress applied on the shaft.

rupture lifetime graph).

Obtain the value of stress for the material S-590 alloy from figure 8.31(Stress versus Rupture life time of 1000 hrs at a temperature of 925°C, the stress is σ = 43 MPa.

Calculate the area of the bar.

A=π/4 * d^2

Here, d'is the diameter of the bar.

Substitute 0.0203 m for d.

A =π/4(0.0203)^2

=3.23x10^-4 m²

Substitute 3.23×10^-4 m² for A, (43×10^6)N/m² for σ in equation (1).

(43x10)= F/(3.23×10^-4)

F = (43×10^4)(3.23×10^-4)

=13889 N

Therefore, the maximum load of 13889 N is required to survive the condition.

Learn more about Load here:

https://brainly.com/question/27960749

#SPJ4

A high compression ratio may result in;

Answers

A high compression ratio may result in compressor failure.

What is a compressor?

A compressor refers to a mechanical device that is designed and developed to provide power to refrigerators, especially by increasing the pressure on air or other applicable gases.

According to heating, ventilation, and air conditioning (HVAC) information, a high compression ratio of 8: 1 or higher is most likely to result in compressor failure.

Read more on compression ratio here: https://brainly.com/question/13756099

#SPJ1

In vertical crankshaft engines equipped with a slinger/governor gear and the proper crankcase oil level, approximately how much of the governor gear is located above the oil surface

Answers

"1/2" is the right response to this question. Approximately half of the governor gear in vertical crankshaft engines that have a slinger or governor gear and the correct amount of oil in the crankcase is placed above the oiled surface. Draining the oil from the top oil fill tube, as well as the fuel tank and the engine, should be done when the governor gear is about halfway through its rotation.

This is further explained below.

What is a crankshaft?

Generally, Engine connecting rods are joined to the crankshaft through the crank mechanism, which is made up of many rotating parts, including the crankshaft, the crankpins, and the crankshaft gears.

In conclusion, "1/2" is the right answer. About half of the governor gear is visible above the oil surface in vertical crankshaft engines with a slinger or governor gear. In order to drain the oil from the top oil fill tube, both the fuel tank and the engine should be at about half of the governor gear after it is completed.

Read more about crankshaft

https://brainly.com/question/9782058

#SPJ1

featers of first generation computers

Answers

The features of first generation computers.It involved the use of vacuum tubes to make electrical circuits.First generation computers made use of magnetic drums.The instructions were written using machine language and symbols.First generation computers had very small storage space.They used punch cards as input and output (I/O) devices.First generation computers were huge in size and poor in mobility.First generation computers had less reliable output and were very slow.First generation computers used high level of electricity.

What are first generation computers?

First generation computers were also referred to as vacuum-tube computer and they can be defined as a type of computer system that were designed and developed to make use of vacuum tubes for their logic circuitry.

Read more on first generation computers here: https://brainly.com/question/10937733

#SPJ1

Complete Question?

What are the features of first generation computers?

The double T-beam is fabricated by welding the three plates together as shown.
The weld can resist a shear stress tau_allow = 100 MPa Determine the maximum shear V that can be applied to the beam.
Express your answer to three significant figures and include appropriate units.

Answers

The maximum shear V that can be applied to the double T-beam is 10 kN.

What is T-beam?

T-beam is a type of structural beam that is shaped like a letter T. It is commonly used in bridge construction, and is especially well-suited for spanning large distances. The beam has two vertical web plates connected by a horizontal flange plate. It is often constructed using reinforced concrete, or steel. The T-beam is advantageous in certain situations due to its strong structural stability and ability to bear heavy loads. Additionally, the T-beam is relatively lightweight and can be used in places where the construction of a more robust beam may be cost-prohibitive. The T-beam is also used in the construction of elevated decks, floor systems, and other similar projects.

The shear force V determines the shear stress τ in the welded joint. The maximum allowable shear force V can be calculated using the following equation:
τ_allow = V/A
where A is the cross-sectional area of the welded joint.
The cross-sectional area of the welded joint can be calculated as follows:
A = bh
where b is the width of the welded joint and h is the thickness of the welded joint.
Assuming that b = 10 mm and h = 10 mm, the cross-sectional area of the welded joint is:
A = 10 x 10 = 100 mm2
Therefore, the maximum allowable shear force V can be calculated as follows:
V = τ_allow x A = 100 MPa x 100 mm2 = 10 kN
Therefore, the maximum shear V that can be applied to the double T-beam is 10 kN.

To learn more about T-beam
https://brainly.com/question/28163882
#SPJ4

Answer:

10 kn

Explanation:

Thanks. I tried hard. I can garrentee it's correct

TRUE OR FALSE a page with a mismatch between the location of the page and the rating location; for example, an english (uk) page for an english (us) rating task.

Answers

A simple query is one that can be explained in a very little number of words. The special form of a known query is a know simple query.

If the answer appears at the very top of the landing page but is not displayed in the result for a Know Simple query, it can still receive a Fully Meets grade. B) Untrue. Explanation: The special form of a know query is a know simple query. What is the length of a cricket ground's pitch, for example, is one such question. A simple query is one that can be explained in a very little number of words. A known simple query would only receive a rating of 100% meet if the displayed result was in a specific result block or was displayed upfront. In this case, clicking a link won't help you find the solution.  

Learn more about Simple query here:

https://brainly.com/question/14367482

#SPJ4

When jumping a dead battery, which car do you start first?

Answers

When jump starting a dead battery, the car with the working battery (the "donor car") should be started first and left running for a few minutes.

Then, the cables should be connected in the following order:

1) positive cable to the positive terminal of the dead battery,

2) other end of the positive cable to the positive terminal of the working battery,

3) negative cable to the negative terminal of the working battery, and

4) other end of the negative cable to a metal surface on the car with the dead battery (not to the negative terminal of the dead battery). Once the cables are connected, the car with the dead battery should be started. If the dead battery is too far gone, jump starting may not be enough to get it running again.

To learn more about dead battery, visit: https://brainly.com/question/30013310

#SPJ4

Which terms could be used as the first term of the expression below to create a polynomial written in standard form? Select five options.

+ 8r2s4 – 3r3s3

StartFraction 5 s Superscript 7 Baseline Over 6 EndFraction
s5
3r4s5
–r4s6
–6rs5
StartFraction 4 r Over s Superscript 6 Baseline EndFraction

Answers

The terms that could be used as the first term of the expression are [tex]3r^4s^5[/tex], [tex]-r^4s^6[/tex], and [tex]-6rs^5[/tex]. The correct options are B, C, and D.

What is polynomial?

A polynomial is a mathematical statement made up of coefficients and indeterminates that uses only the operations addition, subtraction, multiplication, and powers of positive integers of the variables.

Here, it is given that:

+8r²s⁴ - 3r³s³

Now, each of the polynomial's two terms will have a degree of six. This is thus because the degree is equal to the sum of their exponents.

For +8r²s⁴, we add the exponents to get 2 + 4 = 6

Also for 3r³s³, we add the exponents to get 3 + 3 = 6, -r⁴s⁶ can start the polynomial because it has a degree of 4 + 6 = 10.

The degree of -6rs⁵ is 6 but it can also start the polynomial because the exponent of s is greater than the other two in the given expression.

Thus, the correct options are B, C, and D.

For more details regarding polynomial, visit:

https://brainly.com/question/11536910

#SPJ1

QUESTION:
Which statement is true about portable fire extinguishers?
POSSIBLE ANSWERS:
OAir-pressurized water extinguishers put out electrical fires.
Dry chemical, sodium bicarbonate extinguishers put out most fires.
Dry chemical, mono ammonium phosphate extinguishers put out flammable liquid fires.
OCarbon dioxide extinguishers put out wood fires.
Submit Answer
Skip Question
Review/Edit Your Answer

Answers

Until emergency assistance arrives, portable fire extinguishers can put out or manage a fire.

When should Portable fire extinguishers be used?

The use of portable fire extinguishers can put out or contain a fire until emergency assistance is received.

Utilize portable units exclusively for small flames or fires that are still in the early stages because their discharge times are often only a few seconds. Make a plan for a getaway. Avoid breathing in the extinguishing agent and smoke by keeping low to the ground.

Only use a portable fire extinguisher when a fire is small, restricted to a single area, and not made up of extremely flammable materials. If the fire becomes out of control, leave the premises right away and get assistance.

To learn more about fire extinguishers refer to:

https://brainly.com/question/17687941

#SPJ1

(a) Describe the various strategies for dealing with the problem of self-occlusion in object data capture

Answers

The strategies for dealing with the problem of self-occlusion in object data capture are:

The use of a tracking methods that is said to handle occlusion via the modelling of the object motion though the use of linear and non-linear dynamic models. The derived models is known to be often used in telling the object location if a tracked object is said to be occluded until the object shows up again.

What is occlusion in object detection?

Occlusion is known to often takes place if  two or more objects are seen too close and are seen to be merged or combine with one another.

Note that in the case above, The strategies for dealing with the problem of self-occlusion in object data capture are:

The use of a tracking methods that is said to handle occlusion via the modelling of the object motion though the use of linear and non-linear dynamic models. The derived models is known to be often used in telling the object location if a tracked object is said to be occluded until the object shows up again.

Learn more about  object detection from

https://brainly.com/question/14675134

#SPJ1

A thin aluminum sheet is placed between two very large parallel plates that are maintained at uniform temperatures T1 = 900 K, T2 = 300 K and emissivities ε1 = 0.3 and ε2 =0.7, respectively. Thin aluminum sheet has an ε3 of 0.1 facing on the sides of plate 1 and ε3 of 0.2 facing on the sides of plate 2. Determine (a) the net radiation heat transfer between the two plates per unit surface area of the plates (b) compare the result to that without the shield. (c) temperature of the radiation shield in steady operation

Answers

The net radiation heat transfer between the two plates per unit surface area of the plates with shield and without shied are respectively; 2282.76 W/m² and 9766.75 W/m²

How to find the net radiation heat transfer?

We are given;

Temperature 1; T₁

Temperature 2; T₂

Temperature 3; T₃

Emissivity 1; ε₁ = 0.3

Emissivity 2; ε₂ = 0.7

Emissivity 3; ε₃ = 0.2

The net rate of radiation heat transfer with a thin aluminum shield per unit area of the plates with shield is;

Q'₁₂ = σ(T₁⁴ - T₂⁴)]/[((1/ε₁) + (1/ε₂) - 1) + ((1/ε₃,₁) + (1/ε₃,₂) - 1)]

Q'₁₂ = 5.67 * 10⁻⁸(900⁴ - 300⁴)/[((1/0.3) + (1/0.7) - 1) + ((1/0.15) + (1/0.15) - 1)]

Q'₁₂,shield = 2282.76 W/m²

The net rate of radiation heat transfer with a thin aluminum shield per unit area of the plates with no shield is;

Q'₁₂,no shield = σ(T₁⁴ - T₂⁴)]/((1/ε₁) + (1/ε₂) - 1))

Q'₁₂,no shield = 5.67 * 10⁻⁸(900⁴ - 300⁴)/[(1/0.3) + (1/0.7) - 1)]

Q'₁₂,no shield = 9766.75 W/m²

Then the ratio of radiation heat transfer for the two cases becomes;

Q'₁₂,shield/Q'₁₂,no shield = 2282.76/9766.75 = 0.2337 or 4/17

Read more about Net Radiation Heat Transfer at; https://brainly.com/question/14148915

#SPJ1

An axial centric force of magnitude P=450kN is applied to the composite block shown by means of a rigid end plate.

Knowing that h=10mm, determine the normal stress in

(a) the brass core,

(b) the aluminum plates.

Answers

Answer:

Explanation:

To determine the normal stress in the brass core and aluminum plates, we can use the equation of equilibrium:

F = P = A_core * sigma_core + 2 * A_aluminum * sigma_aluminum

where F is the applied force, P is the magnitude of the force, A_core is the cross-sectional area of the brass core, sigma_core is the normal stress in the brass core, A_aluminum is the cross-sectional area of the aluminum plates, and sigma_aluminum is the normal stress in the aluminum plates.

We know that h = 10 mm, and since the cross-sectional area of the brass core is the same as that of the aluminum plates, we can find the cross-sectional area by multiplying h by the width of the block.

A_core = A_aluminum = h * width

We can now use the equation of equilibrium to find the normal stress in the brass core and aluminum plates:

450kN = A_core * sigma_core + 2 * A_aluminum * sigma_aluminum

sigma_core = P / A_core

sigma_aluminum = (P - A_core * sigma_core) / (2 * A_aluminum)

Note that you would need to know the width of the block in order to complete the calculation.

The force of F= 30N acts on the bracket as shown. Determine the moment of the force about the a-a axis of the pipe if \alpha = 60^{\circ} , and \gamma = 45^{\circ} . Also determine the coordinate direction angles of F in order to produce the maximum moment about the a-a axis. What is this moment?

Answers

The coordinate direction angles of F in order to produce the maximum moment about the a-a axis is 14.49Nm and this moment is 15Nm.

What is direction?
Direction
is a term that can refer to a number of different concepts. Generally speaking, direction is a line of travel or an orientation in physical space. Direction can also refer to a goal or purpose for which one is striving, such as a career path or a life path. Directions can also be given in terms of instructions, as in directions for using an appliance, directions for playing a game, or even directions for a recipe.

The moment of the force F about the a-a axis is given by:

M = F × d × sin(\alpha + \gamma)

M = 30N × 0.5m × sin(60° + 45°)

M = 30N × 0.5m × 0.9659

M = 14.49Nm

The coordinate direction angles of F in order to produce the maximum moment about the a-a axis are (45°, -45°). The maximum moment is given by:

M = F × d × 1

M = 30N × 0.5m × 1

M = 15Nm

To learn more about direction
https://brainly.com/question/13088407

#SPJ4

Other Questions
(4n^4-7n^3-29n^2-29n+4)/(n-4) Synthetic Division Who observed the variation of organism in Gala? the mean of 2,10,9 is what Chooe the correct optionThi quetion i required. *AI think the how i about tarting now. BI think the how i about in tart now. CI think the how i about to tart now In the figure, mGE=99, and mHF=41.What is mGPE?mGPE = Rosalyn's arms feel tired and fatigued after she held her cousin's baby for a few minutes. what area of fitness does she need to improve? (1 point) a cardiorespiratory endurance b body composition c flexibility d muscular strength 1- At the beginning of the story, why do you think Muhammad's stomach growled? PLEASE HELP!!!!Find the greatest common factor. 5x^2a+5xa^2 What are the 3 reasons writers write? ___is the transfer of heat through the movement of a fluid such as water or air. URGENT! Write an expression that represents the volume of the nth chamber. Explain your reasoning. Would a bird enthusiast be more likely to hold an owl-watchingVigil at night or during the day? You have been given an assignment for a magazine. The assignment involves architectural photography. The magazine wants high-contrast black and white abstract images that follow the basics of composition. Choose four elements of composition and explain in detail how you would translate them into architectural photographs. Produce architectural photographs using the chosen rules of composition. (Subject Photography) The general equation for depreciation is given by y = A(1 r)t, where y = current value,A = original cost, r = rate of depreciation, and t = time, in years. If BAC=70, and ABC=60 and CE bisects BCD. then find BCE thanks What led to the rise of Hitler in Germany Class 9? cos(x)= square root of 3 over 2 What does an r value of 0.3 mean? Local activist Daniel Simmons was arrested after using fake ballots to vote more than 20 times in the presidential election. According to arresting officers, Simmons told them that he would do "whatever it took to get a president who would finally end pollution." Which category of potential election problems does the passage describe?A.Voting technologyB.Voter turnoutC.Electoral fraudD.Voter fraud Can nuclei of the same element have different values of Z? Of N? Of A?Check all that apply.1 Nuclei of the same element must have the same values of Z, N, and A.2 Nuclei of the same element can have different values of Z.33 Nuclei of the same element can have different values of A.4 Nuclei of the same element can have different values of N.Can nuclei of different elements have the same values of Z? Of N? Of A?Check all that apply.1 Nuclei of the same element can have the same values of Z.2 Nuclei of the same element must have different values of Z, N, and A.3 Nuclei of the same element can have the same values of N.4 Nuclei of the same element can have the same values of A.